HP OMNIBOOK 3000 Скачать руководство пользователя страница 24

Страница: 24 / 86

2-6

Removal and Replacement

HP OmniBook 3000

Figure 2-4. Installing a Hard Drive in the Carrier

Reassembly Notes

•

Depending on the manufacturer of the replacement drive, the hole placement for the four screws
may vary. However, only the indicated IBM drives are qualified at this time.

Important

If you are installing a new hard drive, you should create a Hibernate partition on the drive before
loading any software—see the steps below.

Creating a Hibernate Partition

1. If you do not have an OmniBook 3000 Support Utility floppy disk, create one now. After inserting a

formatted floppy disk: in the floppy drive, do one of the following:

On a factory software installation, click Start, Programs, OmniBook, Create Support Utility
Disk.

On any computer, run

makesupp

from the \Omnibook\Drivers\Hputils directory on the

OmniBook 3000 Recovery CD.

On any computer, download the Support Utility software package from the OmniBook website
(see page vi). Follow the instructions provided.

2. Insert the Support Utility disk in the OmniBook floppy drive.

3. Reboot the computer.

4. When prompted, select “Create Hibernate Partition.”

We recommend that you create a 144-MB partition, the same as the factory setup.

HDD Carrier Kit
F1391-60937
(includes M3.0×5mm screws,
F1391-60950)

Содержание OMNIBOOK 3000























































































Результаты поиска

Содержание OMNIBOOK 3000

Отзывы:

Похожие инструкции для OMNIBOOK 3000

Бренды по названию

Популярные бренды

HP OMNIBOOK 3000, Руководство по обслуживанию

Результаты поиска

Содержание OMNIBOOK 3000

Отзывы:

Похожие инструкции для OMNIBOOK 3000

Бренды по названию

Популярные бренды