HP OMNIBOOK 3000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 86

background image

HP OmniBook 3000

Product Information

1-3

Turning the OmniBook On and Off

•

On.

Press the blue power button to turn the computer on.

•

Standby.

Occurs automatically if the computer is inactive for about 2 minutes.

•

Suspend.

Press the blue power button briefly (about 1 second) to suspend activity when the

OmniBook is on. The computer resumes your previous work session when you turn it back on.

Closing the lid (for more than 2 seconds) also suspends the computer. (If an external monitor is

connected, closing the lid merely turns off the built-in display and turns on the external display.)

•

Hibernate.

Press Fn+F12. The computer completely shuts down, but your current work session is

first saved to disk. The computer will reboot and restore your previous session when you turn it
back on.

•

Off.

Press the blue power button for more than 4 seconds to completely shut down the computer.

Unsaved data is lost. The computer will reboot when you turn it back on.

Table 1-2. Activating Power Modes

Power Mode

To Enter Mode

To Turn Back On

Standby

(display off)

Allow time-out
or
press Fn+S.

Press any key or the pointing device
to display your current session.

Suspend

(low power, “instant-on”)

Press blue power button for about
1 second
or
close the lid (without external monitor)
or
click Start, Suspend
or
allow time-out.

Press blue power button for “instant-
on” to your current session.

Hibernate

(off, session saved)

Press Fn+F12
or
allow time-out.

Press blue power button to turn on,
reboot, and restore session.

Off

(off, nothing saved)

Press blue power button longer than
4 seconds
or
click Start, Shut Down.

Press blue power button to turn on
and reboot.

Table 1-3. Power Mode Descriptions

Power Mode

Condition

Standby

Reduced-power/stopped state. Everything is in a reduced-power state. Network devices are
maintained. Your current work session continues at turn-on (any key-press).

Suspend

Low-power/stopped state. Lower power state than Standby. Everything is off or in a low-
power state. Network devices are off. Your previous work session resumes at turn-on. For
plug-and-play operating systems, network connections resume at turn-on.

Hibernate

No-power/stopped state. Session is saved on the hard disk. Everything is shut down.
Computer reboots at turn-on and restores previous session and network connections (if
plug-and-play).

Off

No-power/stopped state. Everything is shut down (battery continues charging if ac adapter
is connected). Computer reboots at turn-on and restores network connections (if plug-and-
play).

«
...
7
8
9
10
11
...
»

Содержание OMNIBOOK 3000























































































Отзывы:

Нет отзывов

Похожие инструкции для OMNIBOOK 3000

Бренд: ABB Страницы: 14

Бренд: Federal Signal Corporation Страницы: 13

Бренд: Gateway Страницы: 16

Бренд: Accessory Power Страницы: 36

Бренд: Young Living Страницы: 41

Бренд: PASCO Страницы: 8

Бренд: U-Line Страницы: 3

Бренд: X Rocker Страницы: 12

Бренд: R&S Страницы: 44

Бренд: NuTone Страницы: 6

Бренд: EMX Industries, Inc. Страницы: 18

Бренд: MRMC Страницы: 12

Бренд: Rivers Edge Страницы: 28

Бренд: hepco & becker Страницы: 5

Бренд: MAXWORKS Страницы: 7

Бренд: Metra Electronics Страницы: 20

Бренд: Datel Страницы: 7

Бренд: mumbi Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды