HP OMNIBOOK 3000 Скачать руководство пользователя страница 33

Страница: 33 / 86

HP OmniBook 3000

Removal and Replacement

2-15

Figure 2-12. Removing the Display Case and LCD Bracket

Reassembly Notes

•

Before you install the LCD bracket, secure the inverter/MB cable to the case near the hinge area
with a piece of Kapton tape.

•

Make sure the EPE foam is

not

placed under the LCD bracket. The two flaps go on top of the

bracket.

•

After you install the LCD bracket, secure the LCD/LVDS cable to the bracket near the hinge area
with a piece of Kapton tape.

•

Position the two cables correctly before you install the hinge screws. Both cables should protrude
from the case almost 6 cm (about 2 inches).

•

Install each hinge so the slit in the housing faces into the display case.

•

Before installing the LCD module, make sure the EPE foam is properly positioned inside the LCD
bracket. The two flaps should be on top of the center bar of the bracket.

•

Secure the LCD/LVDS cable to the LCD module with a piece of Kapton tape next to the LCD
connector.

•

Position the cables properly in the hinges before installing the bezel.

•

Make sure the bezel snaps to the case along all edges. Pull to the side to help seat the snaps.

•

Make sure the screw covers stick securely in place.

Screw, M2.5×

3mm

F1391-60955 (2)

Screw, M2.5×

5mm

F1391-60951 (4)

LCD/LVDS Cable
F1391-60961

LCD Bracket
F1391-60962

Inverter PCA
F1391-60908

Display Case
F1391-60910

Hinge
F1391-60925 (2)

Inverter/MB Cable
F1391-60959

EPE Foam
F1391-60926

Note:

Flaps go on top

of the LCD bracket.

Содержание OMNIBOOK 3000























































































Результаты поиска

Содержание OMNIBOOK 3000

Отзывы:

Бренды по названию

Популярные бренды

HP OMNIBOOK 3000, Руководство по обслуживанию

Результаты поиска

Содержание OMNIBOOK 3000

Отзывы:

Бренды по названию

Популярные бренды