HP OMNIBOOK 3000 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 86

background image

2-28

Removal and Replacement

HP OmniBook 3000

Component

Equipment

Removal Procedures

Special Notes

Icon PCA

Phillips screwdriver

Plug-in module (page 2-3).
Display, but only until the
icon PCA is removed
(page 2-8).

The display does not have to
be removed.

Inverter/MB Cable

Phillips screwdriver,
Knife or probe,
3 flat screwdrivers

Plug-in module (page 2-3).
Display (page 2-8).
LCD module (page 2-11).
Display case (page 2-13).

The cable should protrude
about 6 cm from the hinge.
Secure the inverter/MB cable
to the case near the hinge
area with a piece of Kapton
tape.

Inverter PCA

Phillips screwdriver,
Knife or probe

Plug-in module (page 2-3).
LCD module (page 2-11).

Unsnap the inverter PCA from
the display case, then unplug
the cable.
Install an inverter bumper
(F1391-60960) on the PCA.

IR/Icon Cable

Phillips screwdriver

Plug-in module (page 2-3).
Hard drive (page 2-4).
Display (page 2-8).
Keyboard (page 2-11).
Top case (page 2-17).

Remove the screws from the
IR PCA and the speaker
bracket.
Make sure the cable is
clamped by the bracket, and it
routes through the bottom
corner of the window opening.

IR Lens

Phillips screwdriver

Plug-in module (page 2-3).
Hard drive (page 2-4).
Display (page 2-8).
Keyboard (page 2-11).
Top case (page 2-17).

The lens should be flush with
the outside of the case.

IR PCA

Phillips screwdriver

Plug-in module (page 2-3).
Hard drive (page 2-4).
Display (page 2-8).
Keyboard (page 2-11).
Top case (page 2-17).

The IR PCA fits onto the pin
on the top case

LCD/LVDS Cable

Phillips screwdriver,
Knife or probe

Plug-in module (page 2-3).
Display (page 2-8).
LCD module (page 2-11).

The cable should protrude
about 6 cm from the hinge.
Secure the LCD/LVDS cable
to the LCD bracket with a
piece of Kapton tape near the
hinge.
Secure the LCD/LVDS cable
to the LCD module with a
piece of Kapton tape next to
the LCD connector.

Lock Plate

Phillips screwdriver

Plug-in module (page 2-3).
Hard drive (page 2-4).
Display (page 2-8).
Keyboard (page 2-11).
Top case (page 2-17).
Motherboard, but only until
you can lift the front edge
(page 2-20).

Pull up on the lock plate until
it comes out of the bottom
case. It wedges into place.

«
...
44
45
46
47
48
...
»

Содержание OMNIBOOK 3000























































































Отзывы:

Нет отзывов

Похожие инструкции для OMNIBOOK 3000

nanoe CZ-CNEXU1

Бренд: Panasonic Страницы: 108

Бренд: ZAPTEC Страницы: 64

Бренд: ZAPTEC Страницы: 24

VisionBook N15G Plus

Бренд: UMAX Technologies Страницы: 44

Бренд: Lanier Страницы: 3

Бренд: M7 SPEED Страницы: 11

Бренд: Paradox Страницы: 2

Бренд: rako Страницы: 7

Бренд: Saft Страницы: 6

Бренд: Tait Страницы: 46

Бренд: Tait Страницы: 9

Бренд: Tait Страницы: 89

Бренд: Tait Страницы: 20

Toughbook CF-T7BWATZJM

Бренд: Panasonic Страницы: 44

Бренд: SR Suntour Страницы: 10

Бренд: DT Research Страницы: 4

Бренд: Matrix Orbital Страницы: 60

Бренд: Bogen Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды