background image

 

 

FIRST STEPS

INSTALLATION GUIDE

Ultrasonic Sensors Series UFP

For further information please see the data sheet at www.waycon.biz/products/ultrasonic-sensors/

MOUNTING THE SENSOR

WayCon Positionsmesstechnik GmbH would like to thank you for the trust you have placed in us and our 
products. This manual will make you familiar with the installation and operation of our ultrasonic sensors. 
Please read this manual carefully before initial operation!
Unpacking and checking:
Carefully lift the device out of the box by grabbing the housing. After unpacking the device, check it for 
any  visible  damage  as  a  result  of  rough  handling  during  the  shipment.  Check  the  delivery  for 
completeness. If necessary consult the transportation company, or contact WayCon directly.

ELECTRICAL CONNECTION

Ultrasonic  sensors  may  be  installed  in  any  position,  as  long  as  depositions  like  dust,  spray  mist,  or 
condensing humidity are avoided on the sound active membrane. 
It is important to avoid structure-borne sound bridges between the sensor and it's holder. 
In case several ultrasonic sensors are used in one application, it is important to leave sufficient distance  
between them. Otherwise the sensors may interact which leads to false measurement values.
By  using  a  sound  deflection  angle  the  sound  beam  can  be  redirected,  at  the  expense  of  the  sensor's 
maximum measurement range. A plain and hard surface should be used for the defection of the sound 
beam. Redirecting the sound beam with multiple sound deflection angles should be avoided.

UFP-200

Pin 1

+24 V

Pin 2

Teach-In

Pin 3

0 V

Pin 4

Switch, Analog Output

 

Pin 1

+24 V

Pin 3

0 V

Pin 4
Pin 5

Teach-In

UFP-400 to 3500, Analog Output

Analog Output

 

UFP-400 to 3500, Switching Output

Pin 1

+24 V

Pin 2

Switching Point P2

Pin 3

0 V

Pin 4

Switching Point P1

Pin 5

Teach-In

 

Содержание UFP Series









Отзывы: