HP HPE Alletra 6010 Скачать руководство пользователя страница 20

Страница: 20 / 117

Figure 8: Array interface examples (Ethernet and Fibre Channel Ports)

Slot 6

Slot 1

Slot 2

Serial port

OCP expansion slot

Slot 3

Slot 4

Eth0 ports, onboard

5 Slot 5

Serial port

Slot 1

Slot 2

OCP expansion slot

Eth0 ports, onboard

Slot 3

For more information on SFPs and connecting 10GbE ports to your array, see SFP Specifications on page 105.

Installation Checklist

Note: During the intial setup process, you will be prompted for the following information. HPE strongly recommends
that you gather this information prior to starting the setup process.

All network settings represent IPv4 values.

The latest version of this list can be found at http://infosight.hpe.com/welcomecenter.

Value

Description

Item

Domain

Install the HPE Storage Array 20

Documentation Feedback: [email protected]

Содержание HPE Alletra 6010






















































































































Результаты поиска

Содержание HPE Alletra 6010

Отзывы:

Похожие инструкции для HPE Alletra 6010

Бренды по названию

Популярные бренды

HP HPE Alletra 6010, Руководство по оборудованию

Результаты поиска

Содержание HPE Alletra 6010

Отзывы:

Похожие инструкции для HPE Alletra 6010

Бренды по названию

Популярные бренды