HP HPE Alletra 6010 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 117

background image

Table 10: Electrical Requirements

Specification (for each PSU)

Component

HPE Alletra 6010, 6030, 6050 (Regulatory model number NMBLA-0003-800)

800 W power supply (LITE-ON-HSTNS-PL41-1)

•

AC input voltage: 100-240V

•

Maximum rated input current: 9.4-4.5 A

•

Rated input frequency: 50-60 Hz

•

IEC 60320 C14 connector

HPE Alletra 6030, 6050, 6070, 6090 (Regulatory model number NMBLA-0003-1600)

1600 W AC power supply (ASTEC HSTNS-PR62)

•

AC input voltage: 200-240V

•

Maximum rated input current: 8.7A

•

Rated input frequency: 50-60 Hz

•

IEC 60320 C14 connector

1600 W DC power supply (Delta HSTNS-PD70)

•

DC input voltage: -40 to -72V, no tolerance

•

Maximum rated input current: 45A

Power supplies

800 W power supply: IEC 60320 C14 connector

1600 W AC power supply: IEC 60320 C14 connector

Power supply connectors

Type varies by region.

Power cords

Installation of this equipment must comply with local and regional electrical regulations governing the installation of information
technology equipment by licensed electricians. This equipment is designed to operate in installations covered by Article 645
of the National Electrical Code and NFPA 75.

Model Specifications

The latest specifications for the HPE Alletra 6000 storage arrays can be found on the HPE website at:
https://infosight.hpe.com/InfoSight/media/local/active/100/HPE%20Alletra%206000%20Config%20Matrix.pdf .

SFP Specifications

Optical Fiber

The following tables list supported SFP+ and SFP28 optical transceivers for HPE storage array 10GbE cards, 25GbE cards,
and 32Gb Fibre Channel (FC) cards.

SFP+ Specifications (10GbE)

Table 11: Finisar

Description

Description

Item

Finisar FTLX8571D3BCL

Finisar FTLX8574D3BCV

Manufacturer / Part number

Multimode

Multimode

Media type

Hardware and Model Specifications 105

Documentation Feedback: [email protected]

«
...
103
104
105
106
107
...
»

Содержание HPE Alletra 6010






















































































































Отзывы:

Нет отзывов

Похожие инструкции для HPE Alletra 6010

Premier 23231GK

Бренд: ABSCO SHEDS Страницы: 25

Бренд: ABSCO SHEDS Страницы: 23

Бренд: ABSCO SHEDS Страницы: 37

Бренд: ABSCO SHEDS Страницы: 40

Бренд: ABSCO SHEDS Страницы: 18

Бренд: ABSCO SHEDS Страницы: 22

FlashPen "Piko"

Бренд: Hama Страницы: 4

Бренд: Qlogic Страницы: 20

Бренд: QNAP Страницы: 74

Бренд: StorCentric Страницы: 53

Бренд: Yardmaster Страницы: 16

Бренд: Synology Страницы: 26

My Book World Edition WDH1NC10000

Бренд: Western Digital Страницы: 2

Бренд: Dancover Страницы: 36

TeraStation WSS WS5020N6

Бренд: Buffalo Страницы: 115

Бренд: iStorage Страницы: 2

BASIC PRO SERIES

Бренд: Borroughs Страницы: 17

Бренд: AIC Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды