HP HPE Alletra 6010 Скачать руководство пользователя страница 48

Страница: 48 / 117

Drive LEDs

The following shows the drive and LED indicator lights and describes their functions.

Drive fault

Drive operation

Each drive carrier has two LEDs. The following table describes the LEDs.

Table 6: Drive LEDs

Status

LED

•

Amber indicates that the drive has failed or been removed

•

LED off indicates normal drive operation

Drive fault (bottom left)

•

Solid green indicates that the drive is online and ready

•

Blinking green twice per second indicates that the drive is being initialized

•

Blinking green five times per second indicates read/write activity on the drive

Drive operation (top left)

Power Supply LED

The following shows the power supply LED indicator light and describes its function.

1 Power supply status

The following table describes the power supply LED.

Table 7: Power supply LED

Status

LED

•

Solid green indicates that the power supply is working properly.

•

Red indicates that the power supply has failed. Replace the power supply.

•

Amber indicates the power supply is in standby mode. Press and release the power
button on the right front handle of the chassis.

•

No color (LED off) indicates unknown status. Inspect the power source and then
power on the array again. If the LED remains off, replace the power supply.

Power supply status

System Information Label

On the rear of the chassis, the system information label is located at the bottom left in a thin tray. The label extends out for
reference.

Array Components 48

Documentation Feedback: [email protected]

Содержание HPE Alletra 6010






















































































































Результаты поиска

Содержание HPE Alletra 6010

Отзывы:

Похожие инструкции для HPE Alletra 6010

Бренды по названию

Популярные бренды

HP HPE Alletra 6010, Руководство по оборудованию

Результаты поиска

Содержание HPE Alletra 6010

Отзывы:

Похожие инструкции для HPE Alletra 6010

Бренды по названию

Популярные бренды