HP HPE Alletra 6010 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 117

background image

3

1

Riser card

Guide post

2 Groove

d) With the riser card and connector properly aligned, press down on the top of the PCIe cage to seat the riser card in

the connector.

e) Press down on the fastener and turn the fastener tab one half turn (180°) clockwise to secure the PCIe cage.

5. For HPE Alletra 6030, 6050, and 6070 arrays, remove the empty right PCIe cage from the upgrade controller.

Note: If you are upgrading a 6010 array, leave the right PCIe cage of the upgrade controller in place and proceed
to Step 7. The HPE Alletra 6010 array does not include a right PCIe cage.

a) Lift the tab of the fastener and turn the fastener one half turn (180°) counter clockwise to release the PCIe cage.
b) Grasp both sides of the PCIe cage and lift the cage out of the controller.

Upgrade Procedures 99

Documentation Feedback: [email protected]

«
...
97
98
99
100
101
...
»

Содержание HPE Alletra 6010






















































































































Отзывы:

Нет отзывов

Похожие инструкции для HPE Alletra 6010

Бренд: GARDEN MASTER Страницы: 8

Бренд: Gearwrench Страницы: 9

Бренд: Backyard Страницы: 63

Бренд: IBM Страницы: 78

CISCO MDS 9124 - UPDATE FOR SYSTEM STORAGE

Бренд: IBM Страницы: 37

Бренд: IBM Страницы: 2

Бренд: Frontier Страницы: 6

Бренд: Ranger design Страницы: 16

Бренд: Geekworm Страницы: 13

Бренд: Honeywell Страницы: 28

Бренд: Axminster Страницы: 28

Бренд: Argosy Страницы: 1

Бренд: Whalen Страницы: 15

Бренд: Kaser Страницы: 4

XL-RAID-SATA-USB

Бренд: XtendLan Страницы: 20

Бренд: Verbatim Страницы: 2

Бренд: Agilent Technologies Страницы: 14

Бренд: Targus Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды