HP HPE Alletra 6010 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 117

background image

Value

Description

Item

Management Networking

Name of subnet carrying management traffic.

Subnet Name

IP address used to access the array.

Management IP Address

Netmask for the management subnet.

Management Netmask

IP address of the router or gateway the array will use
to access network resources outside of the configured
subnet.

Default Gateway

Secondary IP Address

Standard, Jumbo, or Custom.

MTU Size

When MTU size is set to Custom, this specifies the size
in bytes.

MTU Bytes

Name of the domain the array will be joining.

Domain Name

Assigned Subnet Port

Additional Subnet Port

Support IP address for controller A.

Diagnostics A IP Address

Support IP address for controller B.

Diagnostics B IP Address

Data Networking

Name of subnet carrying data traffic.

Subnet Name

Port used for data traffic.

Port

Data port IP address.

IP Address

Netmask for the data subnet.

Netmask

Standard, Jumbo, Custom

MTU Size

MTU size in bytes.

MTU

IP address used for iSCSI discovery.

Discovery IP Address

Rack Mount Safety Precautions

Observe these safety precautions when you install the storage array or expansion shelf in a rack.

Table 5: Rack Mount Safety Precautions

Precaution

Consideration

If the array or expansion shelf is installed in a closed or multi-unit rack assembly, the operating temper-
ature might be greater than the ambient (room) temperature. Provide adequate cooling so the rack
environment does not exceed 35°C (95°F) as specified by the rack manufacturer.

Operating Ambient
Temperature

Install the equipment in the rack such that each item has ample air flow required for proper cooling.

Cold air comes into the front of the array (drive side) and is exhausted out the back of the array (controller
side) by the fans. Install the array with the front facing the cold aisle and the back facing the hot aisle
in your environment.

Air Flow

Install the HPE Storage Array 22

Documentation Feedback: [email protected]

«
...
20
21
22
23
24
...
»

Содержание HPE Alletra 6010






















































































































Отзывы:

Нет отзывов

Похожие инструкции для HPE Alletra 6010

Бренд: Hallowell Страницы: 6

DSN-4100 Series

Бренд: D-Link Страницы: 2

HD080HJ - 80 GB Hard Drive

Бренд: Samsung Страницы: 2

G2 PORTABLE HX-MU025DC

Бренд: Samsung Страницы: 36

Бренд: Backyard Discovery Страницы: 43

My Passport for Mac

Бренд: Western Digital Страницы: 2

Barracuda 7200.7 ST3120228AS

Бренд: Seagate Страницы: 2

Бренд: LaCie Страницы: 27

Biometric Hard Drive

Бренд: LaCie Страницы: 44

Бренд: Campbell Страницы: 30

ApplianceStor 15MT

Бренд: Rasilient Страницы: 30

Mobile Wi-Fi Pocket Drive

Бренд: Macally Страницы: 71

My Book World Edition WDH1NC10000

Бренд: Western Digital Страницы: 2

Бренд: Addonics Technologies Страницы: 9

DiskStation DS415play

Бренд: Synology Страницы: 16

Бренд: E-Z-RECT Страницы: 2

Бренд: SmartStore Страницы: 16

Save2Data SecureKey

Бренд: Hama Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды