HP HPE Alletra 6010 Скачать руководство пользователя страница 65

Страница: 65 / 117

PCIe card

Thumbscrew

PCIe card holder

Riser card

b) Open the PCIe card holder.

Rubber tab

PCIe card

Connector

PCIe cage slot

c) Pull the PCIe card straight out of the card slot.

7. Insert the new PCIe card.

a) Insert the new PCIe card into the card slot.
b) Align the rubber tabs with PCIe cards, and close the PCIe card holder.
c) Tighten the thumbscrew to secure the PCIe card.

8. Install the PCIe cage into the controller.

•

For the primary cage (left), proceed to Step 9.

•

For the secondary cage (right), proceed to Step 10.

9. Install the primary PCIe cage (left) into the controller.

a) Align the PCIe cage and guide post with the grooves of the controller, and lower the cage into the controller.

Maintenance Procedures 65

Documentation Feedback: [email protected]

Содержание HPE Alletra 6010






















































































































Результаты поиска

Содержание HPE Alletra 6010

Отзывы:

Похожие инструкции для HPE Alletra 6010

Бренды по названию

Популярные бренды

HP HPE Alletra 6010, Руководство по оборудованию

Результаты поиска

Содержание HPE Alletra 6010

Отзывы:

Похожие инструкции для HPE Alletra 6010

Бренды по названию

Популярные бренды