HP HPE Alletra 6010 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 117

background image

Upgrade Procedures

Your HPE storage array can be upgraded to add SSDs to increase capacity, as well as by installing new NICs, FC HBAs, or SCM
cards and cabling additional expansion shelves.

To check supported upgrades for your array, refer to the Array Configuration Matrix available on InfoSight at
:https://infosight.hpe.com/InfoSight/media/local/active/89/HPE%20Alletra%206000%20Config%20Matrix.pdf

Upgrade SSDs

Use this procedure to add SSDs to your HPE storage array or expansion shelves.

Before you begin

Up to 30 minutes

Time required:

New 12-pack of SSDs ordered from HPE

Parts required:

•

Case number

•

Array name or serial number

The array serial number can be found on the pullout System Info tab.

Information required:

Support contact:

HPE recommends using the Maintenance Window functionality within the HPE InfoSight portal to inform HPE Support of
upcoming maintenance windows.

Refer to https://infosight.hpe.com/dashboards/nimble/wellness/maintenance-windows for more information.

You can disable automated support case generation during planned maintenance from the Manage Maintenance Windows
page. After a maintenance window is set, no further communication with HPE Support is required.

Note: You do not have to shut down the array to upgrade drives.

Important:

•

The new set of SSDs for drive set B must all be the same capacity.

•

New drives for drive set B can be the same or different capacity as the drives in drive
set A

•

Review the Configuration Matrix on InfoSight for information on capacity limits.

•

Arrays must be running OS 6.0.0.0 or later.

•

After installation, the new drives must be activated before they are fully functional.

The following figure shows the drive set designations for HPE Alletra 6000 arrays:

Upgrade Procedures 85

«
...
83
84
85
86
87
...
»

Содержание HPE Alletra 6010






















































































































Отзывы:

Нет отзывов

Похожие инструкции для HPE Alletra 6010

HD080HJ - 80 GB Hard Drive

Бренд: Samsung Страницы: 2

G2 PORTABLE HX-MU025DC

Бренд: Samsung Страницы: 36

Бренд: Quantum Страницы: 42

Бренд: Quantum Страницы: 148

Бренд: QNAP Страницы: 24

Бренд: Deuba Страницы: 7

TVS-872N-i3-8G-US

Бренд: QNAP Страницы: 12

Бренд: Onnto Страницы: 40

Бренд: Seagate Страницы: 68

Exos ST2000NM0075

Бренд: Seagate Страницы: 42

Бренд: Acard Страницы: 35

HyperDrive COLORSPACE UDMA2

Бренд: SANHO Страницы: 27

Бренд: Konig Страницы: 33

HTS723212L9A360

Бренд: Hitachi Страницы: 176

HTS723212L9A360

Бренд: Hitachi Страницы: 5

Бренд: R/Evolution Страницы: 2

Бренд: Seagate Страницы: 31

Бренд: Thecus Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды