HP HPE Alletra 6010 Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 117

background image

Regulatory and Safety Information

For important safety, environmental, and regulatory information, refer to this section and to the Safety and Compliance
Information for Server, Storage, Power, Networking, and Rack Products guide available at
http://www.hpe.com/support/Safety-Compliance-EnterpriseProducts.

Regulatory Warnings

This section describes all regulatory warnings that apply to HPE storage arrays.

Regulatory Model Numbers: NMBLA-0003-800, NMBLA-0003-800E, NMBLA-0003-1600

European Union (EU)

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.

Israel

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.

Japan

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.

Saudi Arabia

Warning

HPE storage arrays comply with the CITC Technical Specification CITC IT001.

South Korea

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.

Regulatory and Safety Information 114

Documentation Feedback: [email protected]

«
...
112
113
114
115
116
...
»

Содержание HPE Alletra 6010






















































































































Отзывы:

Нет отзывов

Похожие инструкции для HPE Alletra 6010

Бренд: LaCie Страницы: 29

Бренд: Naterial Страницы: 21

Бренд: trueCall Страницы: 16

Taylor-Wharton XL-65

Бренд: Harsco Страницы: 26

Бренд: Qualstar Страницы: 205

MOBILESTOR MS4UT+(B)

Бренд: Sans Digital Страницы: 2

StorageTek T10000D

Бренд: Oracle Страницы: 51

Бренд: Quantum Страницы: 32

Бренд: Metro DataVac Страницы: 16

AltaVault System

Бренд: NetApp Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Active Crystals FM01SW80

Бренд: Philips Страницы: 2

FM FD35B Series

Бренд: Philips Страницы: 163

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды