HP HPE Alletra 6010 Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 117

background image

2. Remove the existing Standby controller to be upgraded.

a) Disconnect the power cords from the two controller power supplies.
b) Label all cables to ensure proper recabling later, then remove them from the controller.
c) Loosen the left and right thumbscrews to free the controller release levers from the controller.

3

1

Controller

Thumbscrew

2 Controller release lever

d) Pull the controller release levers down until they stop. The controller ejects slightly from the chassis.
e) Supporting the weight of the controller, pull the controller release levers to slide the controller out of the chassis. Then

place the controller on a flat surface.

3

1

Chassis

Controller release lever (open)

2 Controller

Important:

To avoid electrostatic damage, place array components on a grounded anti-static mat. Use an ESD wrist strap
during removal and replacement.

3. Remove the empty left PCIe cage from the upgrade controller.

a) Lift the tab of the fastener and turn the fastener one half turn (180°) counter clockwise to release the PCIe cage.

Upgrade Procedures 97

Documentation Feedback: [email protected]

«
...
95
96
97
98
99
...
»

Содержание HPE Alletra 6010






















































































































Отзывы:

Нет отзывов

Похожие инструкции для HPE Alletra 6010

Бренд: Data General Страницы: 91

EonServ 5000 Series

Бренд: Surveon Страницы: 33

Biometric Hard Drive

Бренд: LaCie Страницы: 44

Бренд: Campbell Страницы: 30

Бренд: Dell EMC Страницы: 70

Бренд: HGST Страницы: 51

Tech Tub2 FTT600

Бренд: Copernicus Страницы: 13

Бренд: GRE Страницы: 24

SIMODRIVE 611-D

Бренд: Siemens Страницы: 189

Бренд: Siemens Страницы: 301

Бренд: Clarke Страницы: 12

GardenSaver GS84-S-FJ

Бренд: OLT Страницы: 36

Бренд: STILLA Страницы: 20

Бренд: Acomdata Страницы: 21

Бренд: Life Fitness Страницы: 30

Бренд: ZyXEL Communications Страницы: 6

Бренд: Costway Страницы: 15

Бренд: ZyXEL Communications Страницы: 364

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды