Hoshizaki KM-320MAH-E Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 59

background image

14

(4) Pump-Out Cycle

LEDs 1, 3, and 2 are on.

Comp remains energized. HGV energizes. WV energizes if

S4 dip switch 3 off and 4 on (LED 4 on). LLV (KM-515MAH-E) and FM de-energize.
PM stops for 2 seconds then reverses for 10 or 20 seconds (S4 dip switch 3 & 4).
Water is removed from the bottom of the water tank through the check valve and
down the drain. At the same time, water flows through the small F/S tube to power
flush F/S. When the pump-out timer terminates, pump-out is complete.

The 1st pump-out occurs after the 1st freeze cycle, then every 10th cycle
thereafter (KM-320MAH-E) or every cycle thereafter (KM-515MAH-E and
KM-650MAH-E). The pump-out frequency control is factory set, and generally no
adjustment is required. However, the pump-out frequency control (S4 dip switch 5 &
6) can be set to have a pump-out occur every cycle, or every 2, 5, or 10 cycles. For
details, see "II.C.3.d) Pump-Out Frequency Control (S4 dip switch 5 & 6)."

(5) Harvest Cycle

LEDs 1, 4, and 2 are on.

Same as the initial harvest cycle. See "II.B.1.a)(2) Initial

Harvest Cycle."
Note: Icemaker continues to cycle until TBC is satisfied or power is turned off. The

icemaker always restarts at the 1-minute fill cycle.

(6) Shutdown

When ice contacts the thermostatic bulb (TBC switch open), TBC shuts down the
icemaker within 10 seconds. TBC is factory set, and generally no adjustment is
required. However, adjustment may be needed in some conditions, particularly at
higher altitude locations.

NOTICE!

Do not adjust S4 dip switch 7 out of the factory

default position. This dip switch must be left in the factory default position or
this icemaker will not operate correctly.

Legend:

CB

–control board;

Comp

–compressor;

FM

–fan motor;

F/S

–float switch;

HGV

–hot

gas valve;

LLV

–liquid line valve (KM-515MAH-E);

PM

–pump motor;

TBC

–thermostatic bin control;

WV

–inlet water valve

«
...
12
13
14
15
16
...
»

Содержание KM-320MAH-E




























































Отзывы:

Нет отзывов

Похожие инструкции для KM-320MAH-E

Бренд: Gaggia Страницы: 7

Бренд: MAGIMIX Страницы: 48

Бренд: Saeco Страницы: 48

Бренд: UFESA Страницы: 41

Бренд: Zamboni Страницы: 20

LEI200 E4S MC PD A/R AUTO

Бренд: BIANCHI VENDING Страницы: 72

Бренд: Kalorik Страницы: 20

Бренд: Ugolini Страницы: 11

Бренд: Hamilton Beach Страницы: 28

Triple Scoop KP300

Бренд: Euro-Pro Страницы: 16

Бренд: Nostalgia Страницы: 43

Бренд: Delta-q Страницы: 142

Бренд: Lelit Страницы: 20

Бренд: Sencor Страницы: 16

Бренд: Spaceman Страницы: 24

Caffeo Varianza CSP

Бренд: Melitta Страницы: 250

Бренд: Novexx Solutions Страницы: 248

Бренд: Jenn-Air Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды