Hoshizaki KM-320MAH-E Скачать руководство пользователя страница 48

Страница: 48 / 59

Freeze-Up - Possible Cause

6. Float Switch

See "IV.D. Float Switch Check
and Cleaning"

a) Dirty, sticking.
b) Defective.

7. Refrigerant Charge

a) Low.

8. Control Board

See "II.C.3. Controls and
Adjustments" and "IV.B. Control
Board Check"

a) Harvest timer (S4 dip switch 1 & 2) set too short.
b) Harvest pump timer (S4 dip switch 7) not in factory default position.

c) Defective.

9. Bin Control

See "IV.C. Bin Control Check"

a) Actuator does not move freely.

10. Thermistor

See "IV.E. Thermistor Check"

a) Loose, disconnected, or defective.

11. Thermostatic Expansion Valve

a) Defective.

12. Hot Gas Valve

a) Closed or restricted.

13. Liquid Line Valve

(KM-515MAH-E)

a) Open.

Freeze Cycle

1. Evaporator

a) Scaled up.
b) Damaged.

2. Spray Tubes and/or Spray

Guides

a) Dirty.
b) Out of position.

3. Refrigerant Charge

a) Low.

4. Control Board

See "IV.B. Control Board Check"

a) Freeze timer (S4 dip switch 9 & 10) set incorrectly.
b) Defective.

5. Inlet Water Valve

a) Leaking by.

6. Float Switch

See "IV.D. Float Switch Check
and Cleaning"

a) Float does not move freely.
b) Defective.

7. Pump Motor

a) RPM too slow.
b) Impeller damaged.

8. Thermostatic Expansion Valve

a) Bulb loose or defective.

9. Liquid Line Valve

(KM-515MAH-E)

a) Restricted.

Содержание KM-320MAH-E




























































Результаты поиска

Содержание KM-320MAH-E

Отзывы:

Похожие инструкции для KM-320MAH-E

Бренды по названию

Популярные бренды

Hoshizaki KM-320MAH-E, Руководство по обслуживанию

Результаты поиска

Содержание KM-320MAH-E

Отзывы:

Похожие инструкции для KM-320MAH-E

Бренды по названию

Популярные бренды