Hoshizaki KM-320MAH-E Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 59

background image

43

D. Float Switch Check and Cleaning

F/S is used to determine that there is sufficient water in the water tank after the 1-minute
fill cycle and after each harvest cycle. F/S is also used to determine that the appropriate
volume of water has been converted into ice before switching out of the freeze cycle. No
adjustment is required.

1. Float Switch Check

To check F/S, follow the steps below.

1) Remove the front panel. Move the control switch to the "OFF" position, then unplug the

icemaker from the mains socket.

2) Remove the base cover, then disconnect one end of the pump tubing to drain the water

tank. See Fig. 3. After the water tank has drained, reconnect the pump tubing.

3) Remove the control box cover.
4) Disconnect the black F/S connector from

CB K5 (black) connector.

5) Check for continuity across F/S leads. With

the water tank empty, F/S should be open.
If open, continue to step 7. If closed, follow
the steps in "IV.D.2. Float Switch Cleaning."
After cleaning F/S, check it again. Replace
if necessary.

6) Reconnect the black F/S connector, then

replace the control box cover in its correct
position.

7) Plug the icemaker back into the mains socket, then move the control switch to the "ICE"

position. Replace the front panel in its correct position. After 1 minute, the 1-minute fill
cycle should end and the initial harvest cycle should begin. If the initial harvest cycle
begins, F/S is good and the check is complete. If the initial harvest cycle does not
begin, continue to step 9.

8) Remove the front panel. Move the control switch to the "OFF" position, then unplug the

icemaker from the mains socket.

9) Remove the control box cover.

10) Disconnect the black F/S connector from CB K5 (BLACK) connector.
11) Check for continuity across F/S leads. With the water tank full, F/S should be closed. If

F/S is closed and the icemaker will not switch from the 1-minute fill cycle to the initial
harvest cycle, replace CB.
If F/S is open, confirm that the water tank is full. If the water tank is not full, check
the water supply, water filters, and inlet water valve. If the water tank is full, follow the
steps in "IV.D.2. Float Switch Cleaning." After cleaning F/S, check it again. Replace if
necessary.

Disconnect This
End of Pump
Tubing to Drain
Water Tank

Base Cover

Fig. 3

«
...
41
42
43
44
45
...
»

Содержание KM-320MAH-E




























































Отзывы:

Нет отзывов

Похожие инструкции для KM-320MAH-E

M39 Dosatron TE

Бренд: La Cimbali Страницы: 6

Бренд: DeLonghi Страницы: 18

Incanto Rondo SUP021YO

Бренд: Saeco Страницы: 16

Бренд: Zojirushi Страницы: 17

Бренд: Krups Страницы: 56

Бренд: West Bend Страницы: 68

Vienna Digital SUP 018D

Бренд: Philips Saeco Страницы: 24

Бренд: Hamilton Beach Страницы: 10

Бренд: La Pavoni Страницы: 44

Бренд: Klarstein Страницы: 26

Бренд: Hamilton Beach Страницы: 2

Бренд: Hamilton Beach Страницы: 6

C212103 ZURICH TS

Бренд: Fetco Страницы: 12

Бренд: Geepas Страницы: 8

firma LF 400 MILK

Бренд: LAVAZZA Страницы: 104

Бренд: Victorio Страницы: 8

Бренд: Fakir Страницы: 32

Бренд: WMF Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды