Hoshizaki KM-320MAH-E Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 59

background image

55

1. Cleaning Procedure

1) Dilute 16 fl. oz. (473 ml) of Hoshizaki "Scale Away" with 3 gal. (11 l) of warm water.
2) Remove all ice from the evaporator and the storage bin.

Note: To remove cubes on the evaporator, remove the front panel and move the control

switch to the "OFF" position. Wait 3 minutes, then move the control switch back
to the "ICE" position and place the front panel back in its correct position. The
harvest cycle starts and the cubes will be removed from the evaporator.

3) Remove the front panel. Move the control

switch to the "OFF" position, then unplug
the icemaker from the mains socket.

4) Remove the insulation panel by lifting up

the panel slightly and pulling it towards you.

5) Remove the base cover, then disconnect

one end of the pump tubing to drain the
water tank. See Fig. 5. After the water tank
has drained, reconnect the pump tubing.

6) In bad or severe water conditions, clean the float switch assembly as described below.

Otherwise, continue to step 7.

a. Disconnect the vent tube and the flush tube from the top of the float switch, then

remove the float switch assembly. Remove the rubber boot from the bottom of the
assembly

b. Remove the retainer rod from the bottom of the float switch housing, then remove

the float. Be careful not to bend the retainer rod excessively when removing it.

c. Wipe down the float switch assembly's housing, shaft, float, and retainer rod with

cleaning solution. Clean the inside of the rubber boot and hose with cleaning
solution. Rinse the parts thoroughly with clean water.

d. Reassemble the float switch assembly and replace it and the rubber boot in their

correct positions. Reconnect the vent tube and the flush tube.

7) Pour the cleaning solution into the water tank.
8) Replace the insulation panel in its correct position.
9) Plug the icemaker back into the mains socket, then move the control switch to the

"WASH" position to start the cleaning process.

10) Replace the front panel in its correct position.
11) After 30 minutes, remove the front panel. Move the control switch to the "OFF" position,

then unplug the icemaker from the mains socket.

12) Disconnect one end of the pump tubing to drain the water tank. After the water tank has

drained, reconnect the pump tubing.

13) Plug the icemaker back into the mains socket, then move the control switch to the "ICE"

position to fill the water tank with water.

14) Replace the front panel in its correct position.
15) After 3 minutes, remove the front panel.

Fig. 5

Disconnect This
End of Pump
Tubing to Drain
Water Tank

Base Cover

«
...
53
54
55
56
57
...
»

Содержание KM-320MAH-E




























































Отзывы:

Нет отзывов

Похожие инструкции для KM-320MAH-E

Бренд: Taylor Страницы: 44

PrimaDonna Exclusive

Бренд: DèLonghi Страницы: 11

Бренд: Smeg Страницы: 35

M2 Barsystem C10

Бренд: Cimbali Страницы: 2

Бренд: Macco Страницы: 72

Бренд: Rancilio Страницы: 16

Бренд: U-Line Страницы: 48

Бренд: Kambrook Страницы: 24

Бренд: Krups Страницы: 11

Бренд: Grundig Страницы: 10

Бренд: Mr. Coffee Страницы: 29

Бренд: Prince Castle Страницы: 9

Бренд: Morris Страницы: 16

KAFFEEAUTOMAT MIT TIMER KA 4030

Бренд: SEVERIN Страницы: 58

Бренд: Sencor Страницы: 10

Бренд: Water Well Страницы: 5

i-Joy Cafe Ultimate

Бренд: Beem Страницы: 100

Бренд: La Marzocco Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды