Hoshizaki KM-320MAH-E Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 59

background image

44

2. Float Switch Cleaning

Depending on local water conditions, scale may build up on F/S. Scale on the switch can
cause the float to stick. In this case, F/S should be cleaned.

1) Remove the front panel. Move the control switch to the "OFF" position, then unplug the

icemaker from the mains socket.

2) Remove the base cover, then disconnect one end of the pump tubing to drain the water

tank. See Fig. 3. After the water tank has drained, reconnect the pump tubing.

3) Disconnect the vent tube and the flush tube from the top of F/S, then remove F/S

assembly and remove the rubber boot from the bottom of F/S assembly. See Fig. 4.

4) Remove the retainer rod from the bottom of F/S housing, then remove the float. Be

careful not to bend the retainer rod excessively when removing it.

5) Wipe down F/S housing, shaft, float, and retainer rod with a mixture of 1 part Hoshizaki

"Scale Away" and 25 parts warm water. Clean the inside of the rubber boot and hose
with cleaning solution. Rinse the parts thoroughly with clean water.

6) Reassemble F/S assembly and replace it and the rubber boot in their correct positions.

Reconnect the vent tube and the flush tube.

7) Replace the base cover in its correct position.
8) Plug the icemaker back into the mains socket, then move the control switch to the "ICE"

position. Replace the front panel in its correct position.

Legend:

CB

–control board;

F/S

–float switch

Fig. 4

Float

Float Switch
Housing

Rubber Boot
and Hose

Retainer Rod

Flush

Vent

Shaft

«
...
42
43
44
45
46
...
»

Содержание KM-320MAH-E




























































Отзывы:

Нет отзывов

Похожие инструкции для KM-320MAH-E

Бренд: Gaggia Страницы: 4

Бренд: Gaggia Страницы: 4

Бренд: Gaggia Страницы: 4

Бренд: Gaggia Страницы: 4

Бренд: Gaggia Страницы: 4

Бренд: Gaggia Страницы: 4

Бренд: Gaggia Страницы: 4

Бренд: Gaggia Страницы: 68

Бренд: Hoshizaki Страницы: 61

Бренд: Ice-O-Matic Страницы: 29

Бренд: Saeco Страницы: 100

Бренд: Jura Страницы: 4

Бренд: BOMANN Страницы: 54

Бренд: West Bend Страницы: 33

Бренд: Salton Страницы: 8

Бренд: Dash Страницы: 32

Бренд: Toastess Страницы: 6

Бренд: Gaggia Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды