Honeywell HPA Скачать руководство пользователя страница 45

Страница: 45 / 68

Idle Count Parameter

The

dle

ount parameter specifies the number of pressure integration times that the microprocessor skips between

output values (see Fig. 8). This command is only operational for the

I=Mn

form of the Integration Time (

)

command. (See the

command for setting integration times.) This parameter can be used to reduce the average

HPB power requirement by as much as 50% when increased response time is acceptable. This parameter is also

used to reduce the reply message traffic on the network bus from HPBs whose response time is not critical.

(Default:

IC=0

)

Note:

OP=W

(watchdog timer) is set, then the

command will not be accepted (other than

IC=0

)

and will cause an

command error condition.

Inquiry:

*dd

Action:

*dd

EEPROM Store: *dd

*dd

IC=

ICcount

*dd

SP=ALL

ICcount

0 to 255

where: 0

causes all integration cycles to be used.

causes 1 of 2 integration cycles to be used.

causes 1 of 3 integration cycles to be used.

causes 1 of 4 integration cycles to be used.

255

causes 1 of 256 integration cycles to be used.

Identification Number

Set the device

entification number. This command is used to set a unique HPB address and/or a group address.

Two sections describe this command based on the ring or multi-drop configuration of the unit.

(Default: device

ID=00, group address=90

)

Inquiry:

*dd

(reply is group number for ring network units and both group number and subaddress for

multi-drop network units.)

Action:

*dd

EEPROM Store: *dd

*dd

ID=

newNumber

*dd

SP=ALL

newNumber

00 99 (must enter a

TWO

digit decimal number)

where: 00

Unit numbers itself 00 (null address) and transmits the message unchanged.

*99ID=00

will change all HPBs in network to null address (see

Note

above).

01-88

Unit numbers itself with device ID newNumber, increments the number by 1, and

transmits the message. This will sequentially number all HPBs in a network, starting

from unit dd, with ID=newNumber (see

Note

above).

Unit numbers itself with device ID 89, changes the number to 99, and transmits

the message.

90-98

Unit assigns itself group address newNumber, and transmits the message unchanged.

Unit does not change its address, changes newNumber to ER and transmits the

message.

Unit does not change its address and transmits the message unchanged.

Содержание HPA





































































Результаты поиска

Содержание HPA

Отзывы:

Honeywell HPA, Руководство пользователя, Страница: 45 / 68

Результаты поиска

Содержание HPA

Отзывы: