Honda SH300I 2006, Руководство пользователя

Страница: 317 / 511

FRONT WHEEL/SUSPENSION/STEERING
15-3
SERVICE INFORMATION
GENERAL
• Raise the front wheel off the ground by supporting the frame securely when servicing the front wheel, suspension and
steering stem. A hoist or equivalent is required to support the scooter.
• A contaminated brake disc or pad reduces stopping power. Discard contaminated pads and clean a contaminated disc
with a high quality brake degreasing agent.
• After installing the front wheel, check the brake operation by applying the brake lever.
• Use only tires marked "TUBELESS" and tubeless valves on rim marked "TUBELESS TIRE APPLICABLE".
• When using the pin spanner, use a 25 cm (10 in) long deflecting beam type torque wrench. The pin spanner increases
the torque wrench’s leverage, so the torque wrench reading will be less than the torque actually applied to the steering
stem adjusting nut. The specification given on this page is actual torque applied to the steering stem adjusting nut, not
the reading on the torque wrench when used with the pin spanner. The procedure later in the text gives the actual and
indicated torque.
• For brake system service (page 17-4).
• For handlebar switch inspection (page 22-18).
SPECIFICATIONS
Unit: mm (in)
TORQUE VALUES
ITEM STANDARD SERVICE LIMIT
Minimum tire tread depth – 1.5 (0.06)
Cold tire
pressure Driver only 200 kPa (2.00 kgf/cm
2
, 28 psi) –
Driver and passenger 200 kPa (2.00 kgf/cm
2
, 28 psi) –
Axle runout – 0.2 (0.01)
Wheel rim runout Radial – 2.0 (0.08)
Axial – 2.0 (0.08)
Wheel balance weight
–
70 g (2.5 oz)
maximum
Fork Spring free length 263.5 (10.37) 257.5 (10.14)
Pipe runout – 0.2 (0.01)
Recommended fork
fluid Honda Ultra Cushion Oil 10W
or equivalent
–
Fluid level 90 (3.5) –
Fluid capacity 151
±
2.5 cm
3
(5.1
±
0.08 US oz, 5.3
±
0.09 lmp oz)
–
Steering stem lock nut 68 N·m (6.9 kgf·m, 50 lbf·ft)
Steering stem adjusting nut – See page 15-30
Steering stem pinch bolt 49 N·m (5.0 kgf·m, 36 lbf·ft)
Fork socket bolt 20 N·m (2.0 kgf·m, 15 lbf·ft) Apply locking agent to the threads.
Handlebar post bolt 128 N·m (13.1 kgf·m, 94 lbf·ft) ALOC bolt: replace with a new one.
Master cylinder holder bolt 12 N·m (1.2 kgf·m, 9 lbf·ft)
Front brake disc socket bolt 42 N·m (4.3 kgf·m, 31 lbf·ft) ALOC bolt: replace with a new one.
Front pulser ring torx bolt
(ABS type only) 8 N·m (0.8 kgf·m, 5.9 lbf·ft) ALOC bolt: replace with a new one.
Front axle nut 98 N·m (10.0 kgf·m, 72 lbf·ft) U-nut.
Front axle holder socket bolt
(right side only) 36 N·m (3.7 kgf·m, 27 lbf·ft) ALOC bolt: replace with a new one.
Caliper mounting bolt 30 N·m (3.1 kgf·m, 22 lbf·ft) ALOC bolt: replace with a new one.