Hitachi RAS-(2-3)HVRN(S)(2) Скачать руководство пользователя

Страница: 92 / 488

4 Electrical Wiring

SMGB0064 rev.0 - 08/2011

4.1 General check

D A N G E R

•

Before installing the electrical wiring or before performing a periodical check, turn OFF the main switch to

the indoor unit and the outdoor unit. For safety reasons, be sure that the indoor fan and the outdoor fan have

stopped.

•

Prevent the wires from touching the refrigerant pipes, the plate or cutting edges and the electrical components

inside the unit, to prevent them getting damaged. In worst cases, a fire may occur.

•

Tightly secure the wires with the cord clamp inside the indoor unit.

N O T E

•

In case of performing a test run operation take especially care because some security features are disabled:

the units will operate during 2 hours without Thermo-OFF, and the 3-minute guard for compressor protection

will not be effective during the test.

•

Fix rubber bushes with an adhesive on the panel when the conduit pipes to the outdoor unit are not used.

•

In forced stopped compressor mode, the compressor operation is OFF.

Содержание RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды

Hitachi RAS-(2-3)HVRN(S)(2), Руководство по обслуживанию

Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды