Hitachi RAS-(2-3)HVRN(S)(2) Скачать руководство пользователя страница 311

Страница: 311 / 488

8 Troubleshooting

301

SMGB0064 rev.0 - 08/2011

8.3.2 Self-checking of the remote control switch

Cases where the CHECK switch is used:

If the remote control switch displays a malfunction.

For the regular maintenance check.

No.

LCD Indication

Indicating

Period

(sec.)

For
1 second

Changing of LCD Indication

For
1 second

For
3 seconds

MODE

The LCD indication changes as
shown in the right figure.

To 11

Simultaneously depress the

following 3 switches. (During

operation, they can be depressed.)

TEMP

After the LCD indication changes

as shown in the right figure, the

RUN indicator flashes twice.

To the next page

The LCD indication changes as

shown below.

The remote control switch

automatically starts to check the

transmission circuit.

The LCD indication changes as

shown below.

Depress all the switches

(13 switches) one by one.

Every time the switch is depressed,

the number of the indication of (A)

part in the figure below increases

one by one.

NOTES:
1. Any order of depressing

switches is available.

Depressing 2 or more switches

simultaneously is invalid and

not counted.

Unless all the switches are depressed,

the checking do not proceed to the next item.

MODE

Only for

cancellation

of EEPROM,

depress the

following

3 switches

simultaneously

during changing

LCD indication.

In case that the transmission circuit is abnormal,

the LCD indication remains as the left figure and

the checking do not proceed to the next item.

TEMP

Turn ON the power source.

Содержание RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды

Hitachi RAS-(2-3)HVRN(S)(2), Руководство по обслуживанию

Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды