Hitachi RAS-(2-3)HVRN(S)(2) Скачать руководство пользователя страница 297

Страница: 297 / 488

8 Troubleshooting

287

SMGB0064 rev.0 - 08/2011

Operation OFF, Power OFF

Thermo - OFF (Note 1)

Alarm (Note 2)

Freeze protection, overheating protection

Instantaneous power failure at outdoor unit, reset (Note 3)

Instantaneous power failure at indoor unit, reset (Note 4)

Stoppage of Cooling operation due to Low Outdoor Air Temperature (<=-7 ºC), Stoppage of Heating Operation due to high Outdoor Air

Temperature, and high indoor air temperature, stoppage of heating operation due to low Outdoor Air Temperature (<=-20 ºC)

Demand, enforced stoppage

Retry due to high pressure increase

Retry due to abnormal high temperature of discharge gas, excessive low suction pressure

Retry due to decrease of discharge gas superheat

Retry due to inverter tripping

Retry due to voltage decrease

Expansion valve opening change protection

Operation mode change over of indoor unit (Note 5)

Enforced thermo-off, when other indoor unit thermo-off

Hot start after 4 hours switch on the outdoor unit

Cold draft protection 2

N O T E

•

Explanation of Terms

Thermo-ON: A condition where an indoor unit is requesting the compressor to operate.

Thermo-OFF: A condition where an indoor unit is not requesting the compressor to operate.

•

Even if stoppage is caused by “Alarm”, “02” is not always displayed.

•

If the transmission between the inverter printed circuit board and the control printed circuit board is not per-

formed during 30 seconds, the stoppage cause is d1-05 and the alarm code “04” may be displayed.

•

If the transmission between the indoor unit and the outdoor unit is not performed during three minutes, the

Indoor Units are stopped.
In this case, the stoppage cause is d1-06 and the alarm code “03” may be displayed.

•

In the system “20” will be indicated at the difference between indoor units.

N O T E

•

If a transmission error continues for three minutes, one is added to the occurrence counter.

•

The memorized data can be cancelled by the method which is explained in section 8.3.1 “Self-checking Pro-

cedure of PCB by means of the Remote Control Switch”.

Содержание RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды

Hitachi RAS-(2-3)HVRN(S)(2), Руководство по обслуживанию

Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды