Hitachi RAS-(2-3)HVRN(S)(2) Скачать руководство пользователя

Страница: 203 / 488

7 Test Run

193

SMGB0064 rev.0 - 08/2011

Check list on compressor

CLIENT:

MODEL:

DATE:

Serial No.:

Production date:

Checker:

N°

Check item

Check method

Result

Remarks

Is THM9 correctly connected?

THM9: Discharge gas thermistor

(1) Is wire of thermistor correctly connected by

viewing?

(2) Check to ensure the 7-segment indication of

Td when comp. is operating.

Td: Temperature of THM9

Is thermistor THM9 disconnected?

(1) Check to ensure that thermistor on the top

of comp. is correctly mounted by viewing?

(2) Check to ensure that actually measured

temp. is the same as the indication during

check mode.

Is current sensor faulty?

(1) Check to ensure that indication A1 and A2

are 0 during compressor stopping.

(2) Check to ensure that indication A1 and A2

are not 0 during compressor running.

Is current sensing part on PCB2

faulty?

Is the direction of current sensor

(CTU, CTV) reverse?

Check the direction => by viewing.

Are power source wires, U and

V inserted correctly into current

sensor?

Check to ensure that wires are correctly inser-

ted.

Is exp. valve (MV1) correctly con-

nected?

Check to ensure that MV1 to CN5A is correctly

connected.

Is exp. valve (MV1) coil correctly

connected?

Check to ensure that each coil is correctly

mounted on the valve.

Are the refrigeration cycle and

electrical wiring system incorrectly

connected?

Check to ensure that refrigerant is flowing into

indoor units by operating one refrigerating cycle

only from the outdoor unit.

Is opening of exp. valve completely

closed (locked)?

Check the following by the check mode of

outdoor units.

(1) Liquid pipe temp. (TL) < air intake temp.

(Ti) during cooling operation

(2) Liquid pipe temp. (TL) > air intake temp.

(Ti) during heating operation

Is opening of exp. valve fully ope-

ned (locked)?

Check to ensure that liquid pipe temp. is lower

than air intake temp. of stopping indoor unit

when other indoor units are operating under

cooling operation

Are the contacts for comp. magnetic

switch CMC1 faulty?

Check the surface of each contact (L1, L2 and

L3) by viewing.

Is there any voltage abnormality

among L1-L2, L2-L3 and L3- L1?

Check to ensure that voltage imbalance is sma-

ller than 3%. Please note that power source

voltage must be within 380 V or 220 V+10%.

Is the comp. oil acidified during

compressor motor burning?

Check to ensure that the oil color is not black.

Содержание RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды

Hitachi RAS-(2-3)HVRN(S)(2), Руководство по обслуживанию

Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды