Hitachi RAS-(2-3)HVRN(S)(2) Скачать руководство пользователя страница 188 | Manualshive

Страница: 188 / 488

background image

7 Test Run

178

SMGB0064 rev.0 - 08/2011

7.3 Test run procedure using the wireless remote control switch

N O T E

If the wired remote control switch is used or if multiple units (SET-FREE, DC INVERTER and UTOPIA series) are

operating simultaneously, you cannot perform the test run by means of the remote control swirch. If that is the

case, perform the test run by means of the wired remote control switch.

1

: Perform the test run after completing the installation.

•  Set the batteries for the remote control switch.
•  Turn ON the power source of the indoor and outdoor units.
•  The yellow LED on the receiver of the the indoor unit flickers

(0.25 seconds ON - 0.25 seconds OFF). Then, the yellow LED
turns OFF. While the LED is flickering, the unit will not operate
because the unit is initializing.

2

: Set the TEST RUN mode

• By pressing the SET switch and the OFF TIME switch simulta-

neously for more than three seconds. The LCD should look like
the LCD on the right figure.
The TEST RUN mode is not operating.

3

: Set the operating mode by pressing the MODE switch. The

TEST RUN mode is operating.

4

: Operate the test run by pointing the transmitter towards the

receiver of the indoor unit. Then, press the RUN/STOP switch.
When the indoor unit receives the command, the yellow LED of the
receiver will turn on briefly.
Make sure that the commands are received well and the selected
mode 3) is set correctly.

«
...
186
187
188
189
190
...
»

Содержание RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

SUNLINE MAGNUM DJ 180

Бренд: York Страницы: 40

Бренд: Panasonic Страницы: 76

Бренд: Panasonic Страницы: 118

Бренд: Samsung Страницы: 10

Бренд: Samsung Страницы: 74

Бренд: Haier Страницы: 4

Бренд: Haier Страницы: 8

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 127

STREMER MC40UVM6

Бренд: Daikin Страницы: 24

Бренд: Gree Страницы: 73

Бренд: Carrier Страницы: 8

PLMB mono 12KE-410

Бренд: Amcor Страницы: 12

Бренд: Saneo Страницы: 49

Бренд: Valeo Страницы: 60

Бренд: Waeco Страницы: 33

Бренд: Dimplex Страницы: 15

Бренд: Trane Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды