Hitachi RAS-(2-3)HVRN(S)(2) Скачать руководство пользователя

Страница: 28 / 488

2 Unit Installation

SMGB0064 rev.0 - 08/2011

Lateral Side Blocked

Upper Side Open

Single Installation

Upper Side Blocked

Stack installation (allowed up to 2 Units)

Upper Side Open

Single Installation

Multiple Installation

Close the part A not to allow the outlet air bypassed. Install to avoid the

drain water from upper unit falling on the lower unit.

Allow 100 mm of space between units. Serial sideways installation

allowed up to two units. Leave open both right and left sides. Close the

part A not to allow the outlet air bypassed. Install to avoid the drain water

from upper unit falling on the lower unit.

Upper Side Blocked

Single Installation

Multiple Installation

Be sure to use the fan direction guide. Close the part A not to allow the

outlet air bypassed. Install to avoid the drain water from upper unit falling

on the lower unit.

Be sure to use the fan direction guide. Allow 100 mm of space between

units. Serial side way installation allowed. but leave open both right and

left sides. Close the part A not to allow the outlet air bypassed. Install to

avoid the drain water from upper unit falling on the lower unit.

Содержание RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды

Hitachi RAS-(2-3)HVRN(S)(2), Руководство по обслуживанию

Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды