Hitachi RAS-(2-3)HVRN(S)(2) Скачать руководство пользователя страница 321

Страница: 321 / 488

8 Troubleshooting

311

SMGB0064 rev.0 - 08/2011

•

Checking procedure for the compressor

CHECK LIST ON COMPRESSOR

Client:

Model:

Date:

Serie No.

Production Date:

Checker:

No.

Check item

Check method

Result

Remarks

Is THM9 correctly connected?
THM9: Discharge Gas Thermistor

1. Is wire of thermistor correctly connected by

viewing?
2. Check to ensure the 7-segment indication of Td

when comp. is operating.

Td: Temperature of THM9

Is thermistor THM9

disconnected?

1. Check to ensure that thermistor on the top of

comp. is correctly mounted by viewing?
2. Check to ensure that actually measured temp. is

the same as the indication during check mode.

Is current sensor faulty?

1. Check to ensure that indication A1 and A2 are 0

during compressor stopping.
2. Check to ensure that indication A1 and A2 are not

0 during compressor running.

Is current sensing part on PCB2

faulty?

Is the direction of current sensor

CTU, CTV) reverse?

Check the direction => by viewing.

Are power source wires, U and

V inserted correctly into current

sensor? .

Check to ensure that wires are correctly inserted

Is exp. valve (MV1) correctly
connected?

Check to ensure that MV1 to CN5A is correctly

connected

Is exp. valve coil (MV1) correctly

connected?

Check to ensure that each coil is correctly mounted on

the valve.

Are the refrigeration cycle and

electrical wiring system incorrectly

connected?

Check to ensure that refrigerant is flowing into indoor

units by operating one refrigerating cycle only from the

outdoor unit.

Is opening of exp. valve

completely closed (locked)?

Check the following by the check mode of outdoor

units.
1. Liquid Pipe Temp. (TL) < Air Intake Temp. (Ti)

during Cooling Operation
2. Liquid Pipe Temp. (TL) > Air Intake Temp. (Ti)

during Heating Operation

Is opening of exp. valve fully

opened locked)?

Check to ensure that liquid pipe temp. is lower than air

intake temp. of stopping indoor unit when other indoor

units are operating under cooling operation.

Are the contacts for comp.

magnetic switch CMC1 faulty?

Check the surface of each contact (L1, L2
and L3) by viewing.

Is there any voltage abnormality

among L1-L2, L2-L3 and L3-L1?

Check to ensure that voltage imbalance is
smaller than 3%.
Please note that power source voltage must be within

380V or 220V+10%.

Is the comp. oil acidified during

compressor motor burning?

Check to ensure that the oil color is not black.

Additional Information for “CHECK LIST ON COMPRESSOR”

Check item

Additional information (mechanism of the compressor failure)

1 & 2

The liquid refrigerant return volume to the compressor is controlled by the discharge gas temperature Td when com-

pressor is operating. If Td thermistor is disconnected, the liquid refrigerant return volume will become small by detect-

ing the temperature even if the actual discharge gas temperature is high. Therefore, this abnormal overheating by

detecting the temperature operation will result in insulation failure of the motor winding.

Содержание RAS-(2-3)HVRN(S)(2)









































































































































































































































































































































































































































































































Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды

Hitachi RAS-(2-3)HVRN(S)(2), Руководство по обслуживанию

Результаты поиска

Содержание RAS-(2-3)HVRN(S)(2)

Отзывы:

Похожие инструкции для RAS-(2-3)HVRN(S)(2)

Бренды по названию

Популярные бренды