Hioki 3532-50 Скачать руководство пользователя страница 80

Страница: 80 / 198

_____________________________________________________________________________________________

4.8 Short Circuit Compensation

______________________________________________________________________________________________

NOTE

When compensation is to be performed for some new frequency:

Input the frequency for compensation using the numeric keypad.

Frequency range which can be set : 42.0 Hz to 5.000 MHz

If you attempt to set a test frequency greater than 5 MHz, it will
automatically be reduced to 5 MHz.
If you attempt to set a test frequency lower than 42 Hz, it will automatically
be increased to 42 Hz.

If you make a mistake during input of the numerical value, press the
key to cancel the input so far, and start again.

When you have completed inputting the numerical value for the frequency,

press the appropriate units key

, or

so as to confirm the

displayed frequency for compensation.

Until the numerical value for the frequency has been input, the units keys

cannot be used.

After the frequency for SPOT compensation has been input as above, press
the

key.

Check again - are the test leads properly shorted together with the shorting
bar?

Содержание 3532-50







































































































































































































Результаты поиска

Содержание 3532-50

Отзывы:

Бренды по названию

Популярные бренды

Hioki 3532-50, Инструкция по эксплуатации

Результаты поиска

Содержание 3532-50

Отзывы:

Бренды по названию

Популярные бренды