Hioki 3532-50 Скачать руководство пользователя страница 71

Страница: 71 / 198

_____________________________________________________________________________________________

4.7 Open Circuit Compensation

______________________________________________________________________________________________

NOTE

SPOT compensation for the same frequency as previously

Just press the

key. SPOT compensation will be started using the same

frequency which was used for the last episode of SPOT compensation.

SPOT compensation for some new frequency

Input the frequency for compensation using the numeric keypad.

Frequency range which can be set : 42.0 Hz to 5.000 MHz

If you attempt to set a test frequency greater than 5 MHz, it will
automatically be reduced to 5 MHz.
If you attempt to set a test frequency lower than 42 Hz, it will automatically
be set to 42 Hz.

If you make a mistake during input of the numerical value, press the

key to cancel the input so far, and start again.

When you have completed inputting the numerical value for the frequency,

press the appropriate units key

, or

so as to confirm the

displayed frequency for compensation.

Until the numerical value for the frequency has been input, the units keys

cannot be used.

After the frequency for SPOT compensation has been input as above, press
the

key.

Check again - are the test leads definitely out of mutual contact?

Содержание 3532-50







































































































































































































Результаты поиска

Содержание 3532-50

Отзывы:

Бренды по названию

Популярные бренды

Hioki 3532-50, Инструкция по эксплуатации

Результаты поиска

Содержание 3532-50

Отзывы:

Бренды по названию

Популярные бренды