18.12.2018
18.12.2018
14
15
EN
EN
Part number
Description
1
Wheels
2
Large washer
3
M8x20 screw
4
Nut
5
Washer
6
Support
7
M8x25 screw
8
Frame
9
Engine
10
Cutting elements
11
Belt cover
Adding engine oil to the oil tank
Place the machine on a flat surface and unscrew the oil tank
cap.
3.3. DEVICE USE
PLEASE NOTE! Before starting the machine, pour motor oil
and fuel. The The machine is delivered without engine oil
or fuel.
1.
Place the machine on an even, stable surface with
the outlet chute pointing in a safe direction.
2.
Check the fuel and oil levels before starting the
machine.
3.
Put the collecting bag on the outlet chute and secure
it so that it does not fall.
4.
Make sure that the main hopper and the additional
loading hopper (not the HT-HECTOR 420 model) are
empty. If there is any material in the machine during
start-up, it may cause the starter cord to suddenly
lock or the machine may overturn, causing serious
injury.
5.
Set the throttle to the lowest speed.
6.
Stand on the side of the loading hopper, standing
steady.
7.
Set the fuel valve to the ON position (see figure 4).
8.
Set the choke lever to the ON position (see fig. 5).
3
4
5
4.1
5.1
1. Loading hopper and outlet outlet chute assembly
a)
Insert the wheel axle [14] into the opening in the
bottom of the frame and secure the connection by
pressing the axle with the screw in the centre of the
opening.
b)
Mount the wheels [1] on the axle [14] using the screw
[3] and the large washer [2].
c)
Mount the support [6] to the frame of the machine
using a washer [5], a nut [4] and screws [7].
2.
Assemble the loading hopper
In order to assemble the loading hopper
a)
Insert the loading hopper hinges [12] into the holes
in the housing on the cutting element [15] and fix it
with screws on the other side.
b)
Slide the outlet chute hinges [13] into the holes in
the cutting element housing of [15] and fix it with
screws on the other side.
3.
Handle assembly
a)
Fix the handle [16] to the frame [8] using screws [16],
washers [17] and nuts [18].
Refuelling
The machine is driven by a four-stroke engine powered by
unleaded petrol. Unscrew the fuel tank cap and pour the
petrol (use a funnel), taking care not to spill the liquid or
exceed the maximum petrol level. The tank should be filled
to a level not blocking the fuel filter visibility.
PLEASE NOTE!
Before starting the machine, fill
the oil and fuel tanks according to the operating
instructions.
Refill the engine oil up to the top level on the dipstick.
1
2
1.1
1.2
2.1
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The machine should be used outside closed spaces, on
a stable, level surface, preferably on grass or on the ground.
Do not place the machine on concrete, tarmac on other
hard surfaces, because chips and other residue ejected by
the machine may bounce off and cause a hazard.
Work conditions
Inspect the material which is to be shredded and make
sure there is enough space above the machine to load the
material.
It is recommended to choose a place of work as close
as possible to the place where the chips are used. This
will reduce the need to carry the processed material to
a minimum.
Keep a safe distance from the chip discharge area. Ensure
which all bystanders, children, animals or valuables are also
at a safe distance from the chip discharge area.
ASSEMBLING THE APPLIANCE
PLEASE NOTE!
Do not attempt to start the machine
until the assembly has been completed. It can cause
serious injury, and damage to the machine. During
assembly, do not touch the blades of the machine
and do not place your hands inside the machine.
b)
Fit the wheel set and secure the joint with screws.
c)
Put the machine in a horizontal position and put the
hopper gasket.
d)
Place the loading hopper onto the gasket and secure
the connection with bolts, washers and nuts.
e)
Mount the loading hopper holder and screw it on
using washers and locking screws.
f)
Attach the additional hoper to the side opening of
the machine and tighten it with washers and screws.
HT-HECTOR 420
PLEASE NOTE!
Before starting the machine, fill
the oil and fuel tanks according to the operating
instructions.
I
II
III
IV
V
HT-HECTOR 212
a)
Lay the machine on its side.
Please note! Please note Do not tilt the machine if
oil and/or fuel are in the tanks because they can spill
out.
Part number
Description
12
Loading hopper
13
Outlet chute
14
Axle
15
Cutting element drum housing
16
Screw
17
Washer
18
Nut
14. When the engine has stopped, move the fuel valve
lever to the OFF position.
Shredding
PLEASE NOTE! Before starting work with the machine, it is
necessary to test its operation without the ground material.
If the machine does not make any suspicious sounds and
there are no leaks, you can continue working.
1.
Slowly insert the material into the loading hopper. Do
not put too much at the same time. After inserting
the material, close the cover on the loading hopper
(applies to the HT-HECTOR 212 model).
2.
If necessary, use a long piece of shredded material to
push the batch.
PLEASE NOTE! Do not put your hands or other parts
of your body into the hopper.
8
9
8.1
9.1
9.
Set the engine switch to the ON position or start the
engine with the cord, as follows:
Place your hand firmly on the engine (check beforehand
that the engine is not hot and if it is, allow it to cool before
taking this step), pull the starter cord handle slowly with the
other hand until you feel resistance, then pull the cord hard.
If the engine does not start, repeat the procedure.
11. When the engine starts and runs smoothly, move the
choke lever to the OFF position.
12. To increase or decrease the engine speed, adjust
the throttle. To increase the speed, move the grip
towards the rabbit image to reduce the speed, move
the grip towards the turtle image.
13. To turn the machine off, turn the engine switch to the
OFF position.
6
7
6.1
10
ATTENTION!
This product’s exploded view can be
found on the last pages of the operating instructions
(pp. 57).
