background image

Contents

Component identification........................................................................... 6

Front panel components......................................................................................................................6
Front panel LEDs and buttons ............................................................................................................6

Front panel LED power fault codes.......................................................................................... 7

Hot-plug drive LED definitions............................................................................................................. 8
NVMe drive components and LEDs.................................................................................................... 9
Chassis server bay numbering.......................................................................................................... 10
Chassis I/O module bay numbering.................................................................................................. 10
System board components................................................................................................................ 11

Processor, heatsink, and socket components........................................................................ 12
DIMM slot locations................................................................................................................ 12
System maintenance switch descriptions............................................................................... 13

Setup...........................................................................................................14

Setup overview..................................................................................................................................14
Installing the chassis into a rack........................................................................................................14
Installing hardware options................................................................................................................14
Installing the server........................................................................................................................... 14
Powering up the chassis....................................................................................................................15
Installing the operating system.......................................................................................................... 15
Registering the server....................................................................................................................... 15

Operations..................................................................................................16

Power down the server .....................................................................................................................16
Removing the hard drive blank..........................................................................................................16
Removing a hot-plug drive.................................................................................................................17
Removing the server......................................................................................................................... 17
Removing the access panel.............................................................................................................. 18
Opening the front bracket..................................................................................................................18
Removing a server blank...................................................................................................................19
Installing a server blank.....................................................................................................................20
Removing the air baffle......................................................................................................................21
Installing the air baffle........................................................................................................................22
Removing the rear support bracket................................................................................................... 22

Hardware options installation.................................................................. 24

Introduction........................................................................................................................................24
Drives................................................................................................................................................ 24

Drive guidelines...................................................................................................................... 24
Installing a hot-plug hard drive................................................................................................24
Installing an NVMe drive.........................................................................................................25

Installing a processor-heatsink assembly..........................................................................................26
Memory options................................................................................................................................. 29

DIMM population information..................................................................................................29
DIMM-processor compatibility................................................................................................ 29
HPE SmartMemory speed information................................................................................... 30

3

Содержание HPE ProLiant XL230k Gen10



















































































Отзывы: