Hettich EBA 200 Скачать руководство пользователя страница 37

Страница: 37 / 66

37/65

Carrying out a test run

↓

START
PULSE

•

Press the key.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

STOP
OPEN

•

Press the key.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

•

Load a rotor place with the switch-off weight (for the
switch-off weight, see the table on page 33).

For angle rotors, use a centrifuging container. In

the case of hematocrit rotors, place the switch-
off weight in the padded shell of the rotor place.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

•

Close the lid.

t/min:s

RPM

>RCF<

↓

•

Press the key.

START
PULSE

A short centrifugation run is carried

out to check the imbalance switch-
off.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

If no imbalance is detected during

the test run, the following error
message will appear.

Press any key to clear the error
message.

Possible cause:

•

The imbalance switch-off is
incorrectly set.

•

The switch-off weight used for the
test run is not heavy enough.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

•

Open the lid.

t/min:s

RPM

>RCF<

↓

STOP
OPEN

•

Press the key once to exit the
"

Imbalance" menu or twice to exit the

" SELECT MENU ".

t/min:s

RPM

>RCF<

Example:

t/min:s

RPM

>RCF<

Содержание EBA 200



































































Результаты поиска

Содержание EBA 200

Отзывы:

Похожие инструкции для EBA 200

Бренды по названию

Популярные бренды

Hettich EBA 200, Инструкции по ремонту

Результаты поиска

Содержание EBA 200

Отзывы:

Похожие инструкции для EBA 200

Бренды по названию

Популярные бренды