Hettich EBA 200 Скачать руководство пользователя страница 36

Страница: 36 / 66

36/65

START
PULSE

•

Only press the key if a PWM offset value
is displayed.
Example:

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

•

Load a rotor place with the setting weight (for the
setting weight, see the table on page 33).

For angle rotors, use a centrifuging container.

In the case of hematocrit rotors, place the
setting weight in the padded shell of the rotor
place.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

•

Close the lid.

t/min:s

RPM

>RCF<

↓

•

Press the key.

START
PULSE

Two short centrifugation runs are

carried out to set the imbalance
switch-off.

Afterwards, a test run can be carried
out to check the imbalance switch-
off.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

Ending the imbalance adjustment

↓

STOP
OPEN

•

Only press the key if no test run is to be
carried out.

The imbalance adjustment will be ended.

t/min:s

RPM

>RCF<

↓

Continued on next page

Содержание EBA 200



































































Результаты поиска

Содержание EBA 200

Отзывы:

Бренды по названию

Популярные бренды

Hettich EBA 200, Инструкции по ремонту

Результаты поиска

Содержание EBA 200

Отзывы:

Бренды по названию

Популярные бренды