manualshive.com logo in svg

Hettich EBA 200, Инструкции по ремонту

Поделиться
Скачать
Hettich EBA 200 Скачать руководство пользователя страница 7

 
 

 

7/65 

 

4.3 

Motor (M1) / Speed sensor (B1) 

• 

The motor is a 2-pole three-phase asynchronous motor (1 pair of poles). 

• 

The motor is protected against overheating by an overtemperature switch. The overtemperature switch is 
integrated in the motor and cannot be replaced. 

• 

The electronics (A1) evaluates the overtemperature switch. 

• 

The speed sensor (B1, speedometer) is screwed to the bottom of the motor. The speed signal (1 pulse per 
revolution) will be triggered by a magnet located in the motor axle. 

• 

The electronics (A1) monitors and controls the speed of the motor. 

• 

In addition the speed of the motor is also monitored by the electronics (A2). 

• 

The holder of the magnet for the imbalance detection is attached to the motor. 

 
 

4.4 

Motor-driven lid lock (A4) 

• 

The lid can be opened only if the electronics (A1) has detected rotor standstill. 

• 

After pressing the key 

STOP
OPEN

 the lid opens motor-driven. 

• 

The centrifugation run can only be started when the lid is closed and the lid lock has locked. A microswitch on 
the lid lock detects the position of the lid lock (open/closed) and report it to the electronics (A1). 

 
 

4.5 Imbalance 

detection 

• 

An hall sensor monitors the imbalance. This hall sensor is located on the electronics (A1). 

• 

The magnet for the imbalance detection is located in a holder which is attached to the motor. The holder is 
placed in such a way that the magnet is located directly above the hall sensor. 

• 

Imbalance is detected only in running mode (run up, centrifuging and braking). 

• 

If impermissible imbalance is detected, the motor switches off and the rotor slows down braked until it stops. 

 
 

5 Troubleshooting 

procedures 

• 

Fuses in installation in which centrifuge is installed are intact. 

• 

Mains input fuses of centrifuge are intact. 

• 

Mains voltage present at (see connecting diagram): 

EBA 200: 

− 

Connecting cable 

− 

Appliance plug/mains switch 

− 

Electronics (A1), plug S102L and S102N 

EBA 200 S, HAEMATOKRIT 200: 

− 

Connecting cable 

− 

Appliance plug/mains switch on the electronics (A3), plug SL1 and SN1 

− 

Electronics (A1), plug S100, pin 1 (L1) and pin 3 (N) 

• 

Look for the displayed error message in chapter 6 on page 8. 

• 

Remedy the error according to the instructions. 

• 

Carry out a functional check after every repair and whenever a component is replaced, see pg. 48, chapter 8. 

 

Содержание EBA 200



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды