Hettich EBA 200 Скачать руководство пользователя страница 38

Страница: 38 / 66

38/65

7.4.3

Hiding the display of the centrifuge model

The centrifuge model displayed after switching on the device can be hidden.

With the rotor at a standstill, the display of the centrifuge model can be hidden as follows:

The procedure can be aborted at any time by pressing the

STOP
OPEN

key. In this case, the settings are not stored.

START
PULSE

STOP
OPEN

•

Keep both keys pressed and
switch on the mains switch at
the same time.

t/min:s

RPM

>RCF<

↓

SELECT

•

Press the key until the following is
displayed:

t/min:s

RPM

>RCF<

↓

START
PULSE

•

Press the key.

OEM version :

Hide the display of the

centrifuge model.

off :

Centrifuge model is displayed.

on :

Centrifuge model is not displayed.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

•

Set

off

with the keys.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

START
PULSE

•

Press the key to save the setting.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

STOP
OPEN

•

Press the key once to exit the
"

Setup" menu or twice to exit the

" SELECT MENU ".

t/min:s

RPM

>RCF<

Example:

t/min:s

RPM

>RCF<

Содержание EBA 200



































































Результаты поиска

Содержание EBA 200

Отзывы:

Похожие инструкции для EBA 200

Бренды по названию

Популярные бренды

Hettich EBA 200, Инструкции по ремонту

Результаты поиска

Содержание EBA 200

Отзывы:

Похожие инструкции для EBA 200

Бренды по названию

Популярные бренды