Hettich EBA 200 Скачать руководство пользователя страница 23

Страница: 23 / 66

23/65

START
PULSE

•

Press the button to save the setting.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

STOP
OPEN

•

Press the key once to exit the "

Settings"
menu or press twice to exit the
" MACHINE MENU ".

t/min:s

RPM

>RCF<

Example:

t/min:s

RPM

>RCF<

7.2.3

Optical signal after ending the centrifugation run

The backlighting of the display flashes after the centrifugation run to visually signalize that the centrifugation run has
finished.

The optical signal can be switched on or off when the rotor is at a standstill:

The procedure can be aborted at any time by pressing the

STOP
OPEN

key.

SELECT

•

Press and hold the button for eight
seconds.

t/min:s

RPM

>RCF<

↓

SELECT

•

Press the key until the following is
displayed.

t/min:s

RPM

>RCF<

↓

START
PULSE

•

Press the key.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

SELECT

•

Press the key until one of the following is
displayed:

End blinking :

Backlighting of display

flashes after the centrifugation run.

off :

Backlighting does not flash.

on :

Backlighting flashes.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

•

Set

off

with the keys.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

START
PULSE

•

Press the button to save the setting.

t/min:s

RPM

>RCF<

t/min:s

RPM

>RCF<

↓

STOP
OPEN

•

Press the key once to exit the "

Settings"
menu or press twice to exit the
" MACHINE MENU ".

t/min:s

RPM

>RCF<

Example:

t/min:s

RPM

>RCF<

Содержание EBA 200



































































Результаты поиска

Содержание EBA 200

Отзывы:

Похожие инструкции для EBA 200

Бренды по названию

Популярные бренды

Hettich EBA 200, Инструкции по ремонту

Результаты поиска

Содержание EBA 200

Отзывы:

Похожие инструкции для EBA 200

Бренды по названию

Популярные бренды