HermanMiller Embody 100210688 Скачать руководство пользователя страница 15

Страница: 15 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YJC REV A

Align the spine to the tilt, and seat loca-
tor post and clips to the to the back
attachment points as shown in the fig-
ure on the right. Replace the Seat Clips
as shown in the figure below if they
popped off during step 4.

The Seat back posts should engage
into the Seat Clips as illustrated in the
figures below.

Tilt

Clip

Post

Check to make sure the seat fabric flaps, are
secure over the seat clips and do not visibly pro-
trude where the spine engages the seat.

Clip

Note. If Clips pop off replace them as shown
in Step #25.

Содержание Embody 100210688

































































































































Результаты поиска

Содержание Embody 100210688

Отзывы:

Бренды по названию

Популярные бренды

HermanMiller Embody 100210688, Руководство пользователя

Результаты поиска

Содержание Embody 100210688

Отзывы:

Бренды по названию

Популярные бренды