HermanMiller Embody 100210688 Скачать руководство пользователя страница 122

Страница: 122 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YHP REV A

Embody

™

Cylinder Replacement

PARTS INCLUDED:

TOOLS REQUIRED:

Cylinder

Hammer

Nylon Cap

Flat Screwdriver

Raise chair seat to highest position. Lay chair
on back.

1.Slide flat head screw driver blade under
cable collar and pry up gently until cable collar
is free.

Cable collar

Lift-Off Tool

2.Grasp the cable and push it forward to
release the ball end from cylinder.

Содержание Embody 100210688

































































































































Результаты поиска

Содержание Embody 100210688

Отзывы:

Бренды по названию

Популярные бренды

HermanMiller Embody 100210688, Руководство пользователя

Результаты поиска

Содержание Embody 100210688

Отзывы:

Бренды по названию

Популярные бренды