HermanMiller Embody 100210688 Скачать руководство пользователя страница 107

Страница: 107 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YHR REV C

Strike end of knock off tool with hammer to
separate tilt from cylinder. Remove Tilt.

Set replacement Tilt onto Base/Cylinder
assembly. Firmly push down on Tilt.

Position Rack onto assembly. Install
Flange Bushing and Shoulder bolt.

Shoulder Bolt

Flange Bushing

Tighten Shoulder Bolts to 250 in/lbs.

Install 2 Hex Washer Screws. Tighten
Screws to 55 in/lbs.

Hex Washer
Head Screw

Insert Tilt Limiter Lever into assembly.

Tilt Limiter Lever

Содержание Embody 100210688

































































































































Результаты поиска

Содержание Embody 100210688

Отзывы:

Бренды по названию

Популярные бренды

HermanMiller Embody 100210688, Руководство пользователя

Результаты поиска

Содержание Embody 100210688

Отзывы:

Бренды по названию

Популярные бренды