heinzinger ERS Compact Series Скачать руководство пользователя страница 29

Страница: 29 / 114

Heinzinger electronic GmbH

Phone: +49 (0) 8031 2458 0

www.heinzinger.com

Anton-Jakob-Str. 4, 83026 Rosenheim

Fax: + 49 (0) 8031 2458 58

[email protected]

Germany

Page 29

ERS COMPACT

1.9.5

Options

These options are usually ordered along with the device, as they are permanently built in or preconfigured during

the manufacturing process.

POWER RACKS

19“ rack

Racks in various configurations up to 42U as parallel systems are available, or mixed

with electronic load devices to create test systems. Further information in our product

catalogue, on our website or upon request

Water cooling

Replaces the standard cooling blocks of the internal power stages by three interconnected,

water cooled blocks with two taps led out for supply. This options helps to avoid heating
up the environment due to exhausted heat caused by a certain power dissipation when
the device or a cabinet full of units runs as source.

As a side effect, this type of cooling also reduces audible noise.

1.9.6

The control panel (HMI, standard models)

The HMI (

uman

achine

nterface) consists of a display with touchscreen, two rotary knobs, a pushbutton and

a USB port.

1.9.6.1

Touchscreen display

The graphic touchscreen display is divided into a number of areas. The complete display is touch sensitive and

can be operated by finger or stylus to control the equipment.

In normal operation the left hand side is used to show actual values and set values and the right hand side is used
to display status information:

Actual voltage display

Voltage set value input

Additional status

Status area

Actual current display

Current set value input

Touch area for
rotary knob assignment
DC terminal status

Actual power display

Power set value input

Indicator source/sink mode

Actual resistance display

Resistance set value input

Touch areas for menu
access
Quick menu

Touch areas may be enabled or disabled:

Black text = Enabled

Grey text = Touch area tempo-
rarily disabled

This applies to all touch areas. Some can additionally show a small padlock sign, indicating that

the feature is permanently locked, usually due to a specific setting.

•

Actual / set values area (left hand side)

In normal operation the actual values (large numbers) and set values (small numbers) for voltage, current, power

and resistance on the DC terminal are displayed. For the two operation modes, sink (displayed as

) and source

(displayed as

), there are two separate set values each for current, power and resistance. The two resistance

set values are only displayed while resistance mode is active, while an actual resistance is only displayed during

sink mode operation.

The actual values of current and power can be negative (signed) or positive (unsigned). A negative value belongs

to sink mode and indicates that the device is working as electronic load.

When the DC terminal is switched on the actual regulation mode is displayed as

CV, CC, CP

next to the

corresponding actual value, as shown in the figure above.

The set values can be adjusted with the rotary knobs next to the display screen or can be entered directly via the

touchscreen. When adjusting with the knobs, pushing the knob will select the digit to be changed. Logically, the

values are increased by clockwise turning and decreased by anti-clockwise turning.

Содержание ERS Compact Series



















































































































Результаты поиска

Содержание ERS Compact Series

Отзывы:

heinzinger ERS Compact Series, Руководство пользователя, Страница: 29 / 114

Результаты поиска

Содержание ERS Compact Series

Отзывы: