Hawkeye Mfg AGCO RoGator A Series Скачать руководство пользователя

Страница: 33 / 54

Install the Hawkeye® 2 RCM - Sprayer: RCM - Sprayer Installation

INSTALL THE HAWKEYE® 2 RCM - SPRAYER

ECU CABINET PREPARATION

1. Locate the ECU cabinet on the right side of the machine between the axles, as seen in Figure 1 on page 25, and

remove the cover.

FIGURE 6. Node Mounting Plate Modifications

2. Locate the node mounting plate with the Raven boom/speed sense node and single product node.
3. Remove the bolts securing the boom/speed sense node and single product node to the mounting plate.

NOTE:

Do not disconnect the nodes from the cable connections at this time.

4. Use a socket and socket extension to loosen the bolts securing the node mounting plate to the rear cabinet

wall and remove the plate from the ECU cabinet.

5. Remove the Raven AccuBoom node from the machine ECU cabinet. The AccuBoom node will not be reused

with the Hawkeye® 2 system and may be set aside.

6. Tuck the two rectangular node plugs connected to the AccuBoom out of the way at the bottom of the ECU

cabinet. These will not be used in the Hawkeye® 2 system.

NOTE:

It is recommended to cover the unused electrical connections so no water/dust collects on the pins.

7. Locate the two brown connectors labeled “AccuBoom Tee” in the ECU cabinet. Adjust the harness to allow

access to the connectors for future steps.

Boom/Speed

Sense Node

Raven AccuBoom

Node

Raven Single

Product Node

Содержание AGCO RoGator A Series






















































Результаты поиска

Содержание AGCO RoGator A Series

Отзывы:

Похожие инструкции для AGCO RoGator A Series

Бренды по названию

Популярные бренды

Hawkeye Mfg AGCO RoGator A Series, Руководство по установке

Результаты поиска

Содержание AGCO RoGator A Series

Отзывы:

Похожие инструкции для AGCO RoGator A Series

Бренды по названию

Популярные бренды