background image

CHAPTER

5

Install the Hawkeye® 2 RCM - Sprayer: RCM - Sprayer Installation

25

CHAPTER 5

INSTALL THE HAWKEYE® 2 

RCM - SPRAYER

RCM - SPRAYER INSTALLATION

BEST PRACTICES AND RECOMMENDATIONS

• Do not connect battery leads until all cables are installed and connected.
• If a protected mounting location is not available on the equipment, mount the RCM - Sprayer with the 

connectors facing down toward the ground to prevent moisture from accumulating in the RCM - Sprayer 

connections.

RCM - SPRAYER MOUNTING LOCATION

1. Locate the foam marker pump (if applicable) and ECU cabinet between the axles on the right side of the 

machine.

FIGURE 1. RoGator ECU Cabinet Location

NOTE:

If a foam marker is present on the machine, refer to the “RCM - Sprayer Mounting With Foam Marker” 

on page 26.

If Raven Autoboom XRT is already installed on this machine, refer to “RCM - Sprayer Mounting with 

Raven Autoboom XRT” on page 28.

2. Use the supplied u-bolts (P/N 107-0171-852) and 3/8” hardware to secure the RCM - Sprayer mounting plate 

(P/N 107-0235-015) to the outside of the frame structure, roughly 12” behind the ECU cabinet. Mount the plate 

so that the tabs at the bottom of the plate face toward the center of the machine.

Machine ECU 

Cabinet

Содержание AGCO RoGator A Series























































Отзывы: