Hawkeye Mfg AGCO RoGator A Series Скачать руководство пользователя | Manualshive

Страница: 27 / 54

background image

Nozzle Body and Nozzle Control Valve Installation: Boom Cable Routing and Connection

23

NOZZLE BODY AND NOZZLE CONTROL VALVE INSTALLATION

7. Be sure the corrosion inhibitor has coated the NCV contacts and recessed portions of the connector.

NOTE:

To determine if corrosion inhibitor has been applied, inspect for a thick liquid in the bottom of the

connector.

8. Once all boom cables are routed along the boom as desired, begin connecting the boom cables to the

Hawkeye® 2 NCVs previously installed.

9. Use provided cable ties to secure the boom cables to the boom components as needed to ensure they are

secure.

NOTE:

Do not put strain on cables and connections while applying tie-downs.

Do not leave any exposed cable loops that may get caught on crops or other debris while the vehicle

is in use.

Allow enough cable slack for the boom to fully fold and unfold without stretching the harness or

catching on the boom.

10. The inner boom cables will be connected to the RCM TO LEFT/RIGHT chassis cable in a later section.

«
...
25
26
27
28
29
...
»

Содержание AGCO RoGator A Series























































Отзывы:

Нет отзывов

Похожие инструкции для AGCO RoGator A Series

Бренд: Federal Signal Corporation Страницы: 13

Wireless Temperature/Humidity Station

Бренд: DAVIS Страницы: 8

Audio Interface Conectiv

Бренд: M-Audio Страницы: 18

Бренд: Zamel Страницы: 12

7500DX - Phaser Color LED Printer

Бренд: Xerox Страницы: 5

Бренд: OBO Bettermann Страницы: 2

iBoard IB-ZK406

Бренд: APS Auto Parts Specialist Страницы: 3

LCD Touch BacPac

Бренд: GoPro Страницы: 25

Бренд: Thunderbolt Magnum Solar Страницы: 4

Бренд: Nauticam Страницы: 33

Бренд: Stiebel Страницы: 23

ecoCRAFT VKK GB 1206/3-E-H

Бренд: Vaillant Страницы: 48

Бренд: Ikelite Страницы: 2

Бренд: Acebil Страницы: 11

Genuine Bindicator VRF-1000 Series

Бренд: Venture Measurement Страницы: 2

Бренд: Olympus Страницы: 14

Бренд: Ikan Страницы: 6

Power Station II

Бренд: ResMed Страницы: 161

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды