Haulotte Group HTL 3210 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 248

background image

66

2420344510 E

11.11

AUS

Telescopic handlers

D

- Operation

1.2 -

OPERATIONAL CHECKS

1.2.1 - During the warm-up period

Check at the beginning of each work shift or at each change of operator :

• The heating, the defrost system and the windscreen wiper.

• check all lighting systems for proper operation.

1.2.2 - When the engine is running

Check at the beginning of each work shift or at each change of operator :

• Boost pressure P177.

• Service brake and parking brake operation.

• Forward and reverse.

• Each gear.

• Steer in 2 directions with the engine at idling speed. Check each steering mode (Forward and

reverse).

• The horn and the back-up alarm. They must be audible from inside the operator's cab with the engine

running.

• All of the boom and attachment functions should operate smoothly and correctly.

• Perform all additional checks (

Section H - Lubrication and maintenance).

1.3 -

STARTING THE ENGINE WITH A BOOSTER BATTERY

If the engine has to be started with a booster battery (jumper cable...) proceed as follows :

• Never allow the vehicles to come into contact with each other.

• Connect the (+) terminal of the discharged battery to the (+) terminal of the booster battery.

• Connect the terminal - of the back-up battery to the terminal - of the discharged battery.

• Follow the standard starting procedures.

• Remove the cables in reverse order once the machine has been started.

Keep the engine cover closed while the engine is running. "Failure" to comply with these instructions
could result in death or serious injury.

Never jump-start or charge a frozen battery as it could
explode. Do not produce sparks or flames or smoke near
the battery. Lead acid batteries generate explosive
gases when charging. Wear safety glasses. "Failure" to
comply with these instructions could result in death or
serious injury.

«
...
64
65
66
67
68
...
»

Содержание HTL 3210

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HTL 3210

ecot3 PC160LC-8

Бренд: Komatsu Страницы: 51

Victorian Outdoor Elevator

Бренд: AmeriGlide Страницы: 39

Бренд: Komatsu Страницы: 51

Бренд: Komatsu Страницы: 31

Бренд: Kubota Страницы: 115

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды