Haulotte Group HTL 3210 Скачать руководство пользователя страница 54

Страница: 54 / 248

2420344510

E 11.11

AUS

Telescopic handlers

- Pre-operation and controls

3.5.5 - Heating and ventilation

The cab is equipped with a heater that is also used for de misting the windscreen.

The air is circulated via a two-speed fan. To activate the fan, press the heating fan
switch ( P203 ) on the side instrument panel.

Adjust the heating temperature using the knob under the driver's seat.

Adjust the air flow using the air locks and round vents.

Heating and ventilation - HTL4010 - HTL3510

Heating and ventilation - HTL3210

Do not operate the Telehandler for an extended period without ventilating the cab via the ventilation
system.

Always ensure proper ventilation.

A lack of proper ventilation in the cab during use can lead to driver tiredness (oxygen depravation).

Содержание HTL 3210

























































































































































































































































Результаты поиска

Содержание HTL 3210

Отзывы:

Похожие инструкции для HTL 3210

Бренды по названию

Популярные бренды

Haulotte Group HTL 3210, Руководство оператора

Результаты поиска

Содержание HTL 3210

Отзывы:

Похожие инструкции для HTL 3210

Бренды по названию

Популярные бренды