HANGCHA XF Series Скачать руководство пользователя

Страница: 35 / 142

6. Lubrication of mast

Lubricate the following parts periodically
according to the requirements of lubrication
sheet

①

The periods of paint lubrication grease

depend on the truck‘s work condition. If work
is heavy, please paint much more grease on
mast.

②

To assist with the truck‘s operation,

paint some lubrication grease on the surface
where the idler pulley and inside and outside
masts touch.

Paint some lubrication grease on bearing
guide rail.

Warning

When  painting  lubrication  grease;  stop  the
truck  on  a  smooth  road,  engine  off  and  pull
hand  brake.  Avoid  injury  to  hand  or  body,
and  avoid  falling  off  from  high  place.  Keep
safe.

7. Chain Lubrication

Take one brush with engine oil paint both
sides on chain

8. Lubrication grease to below parts, the
detail please see

Lubrication system

drawing

①

Mast bearing lubricate

;

②

Inching pedal lubricate

;

③

Steering axle shaft lubricate

;

④

Steering

knuckle

main

bearing

lubricate

;

⑤

Steering rod bar pin lubricate

;

⑥

Steering cylinder pin lubricate

9. Bolt, nut tighten

Refer to the

Maintain periodic chart

10.

Hub nut torque check

Check if tightening torque of hub nut meets
standard.

Front wheel

①

Hub nut

②

Split-type rim bolt

（

only1-1.8t

）；

③

Half axle bolt

Tightening torque N.m

：

1.0t-1.8t

2.0t-3.5t

Hub nut

157-176

363-490

4.0t-7.0t

8.0t-10.0t

441

～

558

500

～

585

Содержание XF Series















































































































































Результаты поиска

Содержание XF Series

Отзывы:

Похожие инструкции для XF Series

Бренды по названию

Популярные бренды

HANGCHA XF Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание XF Series

Отзывы:

Похожие инструкции для XF Series

Бренды по названию

Популярные бренды