Halytech HYDROSPIDER2 Скачать руководство пользователя страница 134

Страница: 134 / 140

Halytech

hydroSpider2 User’s Manual v1.23

Page 130

was successfully
503 = Configuration update over web interface
has failed

CFG FAIL

1000-1999 = Input count was reset
1000 + Channel ID

INP RST

2000-2999 = Input was calibrated
2000 + Channel ID

INP CAL

3000-3999 = Input was calibrated remotely
3000 + Channel ID

INP RCAL

10000 = Change Setup was entered

ENTRSETP

10001 = Change setup was exited

EXITSETP

10100 = LAN was turned on

LANON

10101 = LAN was turned off

LANOFF

Appendix K3.

Controls

Control records are logged when the state of a control changes.

Primary Identifier

Secondary Identifier

Value

Range:

2000 to 2999

2000 + Control #

2000 is Switched Power
2001 is Open Collector

0 = Output off

OFF CN#

1 = Output on

ON CN#

Appendix K4.

Alarms

Alarm records are logged whenever the state of an alarm changes (activation, deactivation, and
acknowledgement) and when the alarm has something to report about the status of its alerts.

Primary Identifier

Secondary Identifier

Value

Range:

3000 to 3999

3000 + Alarm number

0 = Alarm activated

AL ACT

1 = Alarm deactivated

AL DEACT

2 = Alarm acknowledged

AL ACK

3 = Alarm auto acknowledged

AL ATACK

10000-19999 = Alarm SMS sent OK
(100 x SMS number) + Attempt number

ALSMS OK

20000-29999 = Alarm SMS failed
(100 x SMS number) + Attempt number

ALSMS FL

30000-39999 = Alarm email sent OK
30000 + Attempt number

ALEML OK

40000-49999 = Alarm email failed
40000 + Attempt number

ALEML FL

50000-50099 = Alarm tweet sent OK
50000 + Attempt number

ALTWT OK

50100-50199 = Alarm tweet failed
50100 + attempt number

ALTWT FL

Содержание HYDROSPIDER2













































































































































Результаты поиска

Содержание HYDROSPIDER2

Отзывы:

Бренды по названию

Популярные бренды

Halytech HYDROSPIDER2, Руководство пользователя

Результаты поиска

Содержание HYDROSPIDER2

Отзывы:

Бренды по названию

Популярные бренды