HAKO Citymaster 2000 Скачать руководство пользователя

Страница: 10 / 186

1-4

X56b110.fm

Introduction

1.5 Brief description

The Citymaster has been designed as a tool carrier / machine.
The large number of possible applications make for year-round operation.

In addition to the sweeping equipment, the Citymaster can be equipped

with snow blade or spreader.
The vehicle is equipped as per StVZO (German road use registration).
Its maximum speed is 50 kph with

tyres 215/70 - R15C.
The main components are:

•

Modern and comfortable cab in "space frame design" with 3-fold

adjustable suspension seat for the driver and unsprung passenger's

seat, all-around tinted windows, heated windscreen, warm water

heating

•

4-cylinder turbodiesel engine with 74 kW performance, meets exhaust

standard Euro IV according to 1999/96 EC.

•

Torsionally flexible, welded ladder frame, offset and inclined in the front

part.

•

High driving comfort due to helical springs, auxiliary rubber springs and

hydraulic oscillation stabilisers.

•

Rigid axles on 4 trailing arms each and panhard rod, front axle as

steering and drive axle, rear axle as driving axle, optionally as steering

and drive axle

•

Hydrostatic steering, optionally with four wheel steering (not in transport

mode)

•

Hydrostatic drive with automatic control and differential lock switchable

under load

•

Two drive modes:

1st drive mode 0 – 15 kph

2nd drive mode 0 – 50 kph (0 – 25 kph reverse)

•

Hydraulic 2-circuit brake system with power brakes on front and rear

wheels. Load-dependent brake-power controller on rear axle, mecha-

nical parking brake on separate brake drum on transfer gearbox acting

on the rear axle

•

Powerful, operator-friendly hydraulic system:

•

Adjustable axial piston pump (116 l/min at 210 bar) with front and rear
plug connections

•

Front power lift with mounting triangle, rear power lift (optional)

Содержание Citymaster 2000



























































































































































































Результаты поиска

Содержание Citymaster 2000

Отзывы:

Похожие инструкции для Citymaster 2000

Бренды по названию

Популярные бренды

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Citymaster 2000

Отзывы:

Похожие инструкции для Citymaster 2000

Бренды по названию

Популярные бренды