HAKO Citymaster 2000 Скачать руководство пользователя страница 36

Страница: 36 / 186

3-8

X56b310.fm

Operation

Fig. 16:

101

100

102 103 104 105 106

Pos.

Description

Controls in the roof area

Not used

Interior light

Sun visor (left/right)

Handles (left/right)

Roof console

Telltale - direction indicator (tractor vehicle, green)

Telltale - direction indicator (trailer, green)

Telltale – high beam (blue)

Warning light - battery charging, alternator (red)

Warning light - engine oil pressure (red)

Telltale - engine preheater (yellow)

Warning light – brake fluid level (red)

Not used

Telltale – rear fog light (yellow)

Telltale – window heating and mirror heating (option, green)

Tip switch – working mode/transport mode

Telltale – working mode (orange)

Telltale – transport mode (green)

Not used

Faster winter service in transport mode (option)

Tip switch – differential lock (green)

Rocker switch – rotating beacon (yellow)

Tip switch – front wheel steering/four wheel steering (green)

100

Telltale – four wheel steering (green)

101

Telltale – front wheel steering (green)

102

Not used

103

Not used

104

Not used

105

Tip switch – heated windscreen / heated outside rearview mirror (green)

106

Not used

Содержание Citymaster 2000



























































































































































































Результаты поиска

Содержание Citymaster 2000

Отзывы:

Бренды по названию

Популярные бренды

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Citymaster 2000

Отзывы:

Бренды по названию

Популярные бренды